NVidia GeForce 6100

[edward]

I have a new ASUS MB model NC-AS-M2N-MX which is giving me isues when installing Centos 4.4 64bit
I initially had problems with finding the SATA drives but I resolved that issue by specifying the NVIDIA SATA driver during the initial install.
The install went fine after that, but upon the restart after the install it craps out and locks up when trying to load the video I assume. The display goes crazy ... no mouse, total lockup.

I't seems that the initial install goes fine using the generic VESA driver but I even tried single user mode with no X and still no go so maybe it is some other confict but I don't know what it is.

Maybe someone here has run into a similar situation.

Would appreciate any help that someone could offer in getting this MB working.

Here are the specs of the MB:

–Key Specifications: NC-AS-M2N-MX Form Factor: uATX, 9.6" x 8.8"
CPU
- Support AMD Socket AM2 Athlon 64 X2 / Athlon 64 FX / Athlon 64/ Sempron

Chipset
- NVIDIA nForce430/GeForce6100

Front Side Bus
- 2000 / 1600 MT/s

Memory
- Dual channel memory architecture
- 4 x 240-pin DIMM, support max. 4GB DDR2 800/667/533 ECC and
non-ECC,un-buffered memory
VGA
- Integrated GeForce 6100 GPU
- High Definition Video Processing with max. resolutions to 1920 x 1440

Expansion Slots
- 1 x PCI Express x16
- 1 x PCI Express x1
- 2 x PCI

Storage/RAID
- NVIDIA MCP61P
- 1 x UltraDMA 133/100/66/33
- *4 x Serial ATA 3Gb/s with RAID 0, RAID 1, RAID 0+1, RAID 5 & JBOD
NVIDIA MediaShield? RAID 0, 1, 0+1, 5 and JBOD span cross Serial ATA
drives
LAN
- NVIDIA MCP61P built-in Gigabit MAC with external Attansic PHY

Audio
- ADI AD1986A High Difinition Audio 5.1channel CODEC
- Support Jack-Sensing and S/PDIF out interface

USB
- 10 USB2.0/1.1 ports

Manageability
- WfM 2.0, DMI 2.0, WOL by PME, WOR, PXE, Chassis Intrusion

BIOS
- 4Mb Flash ROM, Award BIOS, PnP, DMI2.0, WfM2.0, SM BIOS 2.3, ACPI 2.0
Overclocking Features
- SFS (Stepless Frequency Selection) from 200MHz to 230MHz at 1MHz
- increment
- Adjustable Voltage :
- *core: @ 0.025V stepping
- *chipset: 2- stepping
- *ddr: 4- stepping
- Overclocking Protection:
- ASUS C.P.R.(CPU Parameter Recall)

Special Features
- ASUS Q-Fan
- ASUS My Logo 2
- ASUS CrashFreeBIOS2
- ASUS EZ Flash 2
Back Panel I/O Ports
- 4 x USB 2.0 ports - 1 x RJ45
- 1 x COM1 - 1 x PS/2 Mouse
- 1 x 5.1 channel Audio I/O - 1 x PS/2 Keyboard

Internal I/O Connectors
- 3 x USB 2.0 connector supports additional 4 USB 2.0 ports
- 1 x S/PDIF output connector
- High Definition Front panel audio connector
- 4-pin CPU Fan / 2*Chassis Fan connectors
- Chassis Intrusion connector
- CD audio-in connector
- 24-pin ATX power connector
- 4-pin ATX 12V Power connector

Accessories
- 1 x Serial ATA cables - 1 x FDD cable
- 1 x SATA power cable - 1 x I/O Shield
- 1 x UltraDMA 133/100/66 cable - User's manual

- 1 x COM1 - 1 x PS/2 Mouse
- 1 x 5.1 channel Audio I/O - 1 x PS/2 Keyboard

Internal I/O Connectors
- 3 x USB 2.0 connector supports additional 4 USB 2.0 ports
- 1 x S/PDIF output connector
- High Definition Front panel audio connector
- 4-pin CPU Fan / 2*Chassis Fan connectors
- Chassis Intrusion connector
- CD audio-in connector
- 24-pin ATX power connector
- 4-pin ATX 12V Power connector

Accessories
- 1 x Serial ATA cables - 1 x FDD cable
- 1 x SATA power cable - 1 x I/O Shield
- 1 x UltraDMA 133/100/66 cable - User's manual

[Michael]

Can you post your xorg.conf? Have you tried installing the NVIDIA drivers? Did you try any other distributions or LiveCDs?

[edward]

Can you post your xorg.conf? Have you tried installing the NVIDIA drivers? Did you try any other distributions or LiveCDs?

I cannot get to a system prompt to install the driver or to access anything else for that matter. It does the same thing with Ubuntu.

[Michael]

What if you enter 3 as an argument from GRUB so it will go to run level 3?

[edward]

What if you enter 3 as an argument from GRUB so it will go to run level 3?

Yes, I tried that as well (init 3) from the kernel line but still no go and that's what has me confused and thinking it may be more than one thing.

[Michael]

Try doing a fresh install?

[edward]

Try doing a fresh install?

I have tried a fresh install 3 times already with the same results.

Even with the live CD I tried specifying (nox nonet etc) because I thought it may be the NIC driver and it still hung-up in the same place when booting.

[Michael]

Have you tried the Fedora LiveCD or anything?