Results 1 to 4 of 4

Thread: A few questions about Test Suite

  1. #1
    Join Date
    Jul 2008
    Posts
    2

    Unhappy A few questions about Test Suite

    Hi, I'm new here and I have a few doubts about your great suite of benchmarking.

    1) Why my proccessor is no detected correcly? Same case with my memory.
    Show the results like this:



    2) Why the sensors not works properly during bench?
    Code:
    $ ./phoronix-test-suite run compliance-sensors
    ====================================
    LM Sensors (Run 1 of 1)
    ====================================

    FAIL,FAIL,FAIL,FAIL,PASS,PASS,PASS

    ################################################## ####
    LM Sensors:

    (VCore, +3.3V, +5V, +12V, CPU Fan, CPU Temp, Sys Temp)

    Final: FAIL,FAIL,FAIL,FAIL,PASS,PASS,PASS

    ################################################## ####

    But the daemon sensors works fine.:S
    I try $ phoronix-test-suite sensor-options:
    Code:
    $ ./phoronix-test-suite sensor-options
    
    Monitoring these sensors are as easy as running your normal Phoronix Test Suite commands but at the beginning of the command add: MONITOR=<selected sensors> (example: MONITOR=cpu.temp,cpu.voltage phoronix-test-suite benchmark universe). Below are all of the sensors supported by this version of the Phoronix Test Suite.
    
    Supported Options:
      - all
      - all.temp
      - all.power
      - all.voltage
      - all.freq
      - all.usage
      - gpu.temp
      - cpu.temp
      - sys.temp
      - battery.power
      - cpu.voltage
      - v3.voltage
      - v5.voltage
      - v12.voltage
      - cpu.freq
      - gpu.usage
    But I don't have to use properly.


    Use Arch Linux i686 x32 - E7200 @3,6 - 1024 mb Kingston DDR2 800 mhz 4-4-4-12 - HD Seagate 320 gigas S-ATA II - GeForce 7300GT - GA-P35-DS3P


    Thanxs in advance.

  2. #2

    Default

    Quote Originally Posted by mojado View Post
    1) Why my proccessor is no detected correcly? Same case with my memory.
    Show the results like this:

    Can you paste the output of your /proc/cpuinfo ?

    Quote Originally Posted by mojado View Post
    2) Why the sensors not works properly during bench?
    Code:
    $ ./phoronix-test-suite run compliance-sensors
    ====================================
    LM Sensors (Run 1 of 1)
    ====================================

    FAIL,FAIL,FAIL,FAIL,PASS,PASS,PASS

    ################################################## ####
    LM Sensors:

    (VCore, +3.3V, +5V, +12V, CPU Fan, CPU Temp, Sys Temp)

    Final: FAIL,FAIL,FAIL,FAIL,PASS,PASS,PASS

    ################################################## ####

    But the daemon sensors works fine.
    Can you then paste the output when running the sensors command?

    Arch Linux always seems to be problematic with PHP / Phoronix Test Suite.

  3. #3
    Join Date
    Jul 2008
    Posts
    2

    Default

    Thanxs Michael!

    Quote Originally Posted by Michael
    Can you paste the output of your /proc/cpuinfo ?
    Code:
    $ cat /proc/cpuinfo 
    processor	: 0
    vendor_id	: GenuineIntel
    cpu family	: 6
    model		: 23
    model name	: Intel(R) Core(TM)2 Duo CPU     E7200  @ 2.53GHz
    stepping	: 6
    cpu MHz		: 3800.059
    cache size	: 3072 KB
    physical id	: 0
    siblings	: 2
    core id		: 0
    cpu cores	: 2
    fdiv_bug	: no
    hlt_bug		: no
    f00f_bug	: no
    coma_bug	: no
    fpu		: yes
    fpu_exception	: yes
    cpuid level	: 10
    wp		: yes
    flags		: fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe lm constant_tsc arch_perfmon pebs bts pni monitor ds_cpl est tm2 ssse3 cx16 xtpr sse4_1 lahf_lm
    bogomips	: 7606.61
    clflush size	: 64
    
    processor	: 1
    vendor_id	: GenuineIntel
    cpu family	: 6
    model		: 23
    model name	: Intel(R) Core(TM)2 Duo CPU     E7200  @ 2.53GHz
    stepping	: 6
    cpu MHz		: 3800.059
    cache size	: 3072 KB
    physical id	: 0
    siblings	: 2
    core id		: 1
    cpu cores	: 2
    fdiv_bug	: no
    hlt_bug		: no
    f00f_bug	: no
    coma_bug	: no
    fpu		: yes
    fpu_exception	: yes
    cpuid level	: 10
    wp		: yes
    flags		: fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe lm constant_tsc arch_perfmon pebs bts pni monitor ds_cpl est tm2 ssse3 cx16 xtpr sse4_1 lahf_lm
    bogomips	: 7603.65
    clflush size	: 64

    Quote Originally Posted by Michael
    Can you then paste the output when running the sensors command?
    Code:
    $ sudo /etc/rc.d/sensors start
    $ sensors
    it8718-isa-0290
    Adapter: ISA adapter
    in0:         +1.25 V  (min =  +0.00 V, max =  +4.08 V)   
    in1:         +1.94 V  (min =  +0.00 V, max =  +4.08 V)   
    in2:         +3.36 V  (min =  +0.00 V, max =  +4.08 V)   
    in3:         +2.99 V  (min =  +0.00 V, max =  +4.08 V)   
    in4:         +0.11 V  (min =  +0.00 V, max =  +4.08 V)   
    in5:         +0.06 V  (min =  +0.00 V, max =  +4.08 V)   
    in6:         +0.00 V  (min =  +0.00 V, max =  +4.08 V)   ALARM
    in7:         +3.10 V  (min =  +0.00 V, max =  +4.08 V)   
    in8:         +3.09 V
    fan1:       2547 RPM  (min =    0 RPM)
    fan2:       1271 RPM  (min =    0 RPM)
    fan3:          0 RPM  (min =    0 RPM)
    fan4:          0 RPM  (min =    0 RPM)
    temp1:       +34.0C  (low  = +127.0C, high = +127.0C)  sensor = transistor
    temp2:       +28.0C  (low  = +127.0C, high = +127.0C)  sensor = thermal diode
    temp3:        -2.0C  (low  = +127.0C, high = +127.0C)  sensor = transistor
    cpu0_vid:   +2.800 V
    
    coretemp-isa-0000
    Adapter: ISA adapter
    Core 0:      +31.0C  (high = +76.0C, crit = +100.0C)  
    
    coretemp-isa-0001
    Adapter: ISA adapter
    Core 1:      +32.0C  (high = +76.0C, crit = +100.0C)
    Code:
    $ ./phoronix-test-suite run compliance-sensors
    
    Would you like to save these test results (Y/n)? Y
    Enter a name to save these results: sens
    Enter a unique identifier for distinguishing this series of tests: 15
    
    ====================================
    LM Sensors (Run 1 of 1)
    ====================================
    
    FAIL,FAIL,FAIL,FAIL,PASS,PASS,PASS
    
    ######################################################
    LM Sensors:
    
    (VCore, +3.3V, +5V, +12V, CPU Fan, CPU Temp, Sys Temp)
    
    Final: FAIL,FAIL,FAIL,FAIL,PASS,PASS,PASS
    
    ######################################################
    
    
    The PHP GD extension must be loaded in order for the graphs to display!
    Results Saved To: /home/jack/.phoronix-test-suite/test-results/sens/composite.xml
    Do you want to view the results in your web browser (y/N)?
    Thanxs for your help and greetings.(Y)

  4. #4
    Join Date
    Nov 2007
    Posts
    20

    Default

    First i like to thank you for this great piece of software !

    While testing around, some things went wrong on my system.

    1. phoronix-test-suite benchmark compliance-ogl

    the output was:

    Code:
    ====================================
    GLEW (Run 1 of 1)
    ====================================
    
    ./compliance-ogl: 2: ./glew/bin/glewinfo: not found
    
    ########################################################
    GLEW:
    
    (GL 1.1, GL 1.2, GL 1.3, GL 1.4, GL 1.5, GL 2.0, GL 2.1)
    
    Final: FAIL,FAIL,FAIL,FAIL,FAIL,FAIL,FAIL
    obviously the binaries were missing / not compiled on installation, so i compiled it by hand and it works like a charme now.

    Code:
    ====================================
    GLEW (Run 1 of 1)
    ====================================
    
    GL_VERSION_1_1:                                                OK 
    GL_VERSION_1_2:                                                OK 
    GL_VERSION_1_3:                                                OK 
    GL_VERSION_1_4:                                                OK 
    GL_VERSION_1_5:                                                OK 
    GL_VERSION_2_0:                                                OK 
    GL_VERSION_2_1:                                                OK 
    
    ########################################################
    GLEW:
    
    (GL 1.1, GL 1.2, GL 1.3, GL 1.4, GL 1.5, GL 2.0, GL 2.1)
    
    Final: PASS,PASS,PASS,PASS,PASS,PASS,PASS
    
    ########################################################

    2. phoronix-test-suite benchmark glmark

    The version 0.5.2 provided by PTS 1.02 segfaults on my system.
    I used 0.5.2.1 from https://sourceforge.net/project/show...roup_id=224203 which works. But i have to enter the resolution by hand to start glmark like this:
    Code:
    ====================================
    GLMark (Run 1 of 1)
    ====================================
    
    
    800
    600
    16
    0
    
        Vertex buffer object          FPS: 1204
    
    ####################################
    GLMark:
    800 x 600 - Vertex Buffer Object
    
    1204 Average FPS
    
    Average: 1204.00 Average FPS
    ####################################
    3. My processor is not detected correctly..
    it says
    Processor: Unknown (Total Cores: 1)
    Here is my output of /proc/cpuinfo:

    Code:
    $ cat /proc/cpuinfo
    processor	: 0
    vendor_id	: AuthenticAMD
    cpu family	: 6
    model		: 10
    model name	: AMD Athlon(tm) XP 2200+
    stepping	: 0
    cpu MHz		: 1804.233
    cache size	: 256 KB
    fdiv_bug	: no
    hlt_bug		: no
    f00f_bug	: no
    coma_bug	: no
    fpu		: yes
    fpu_exception	: yes
    cpuid level	: 1
    wp		: yes
    flags		: fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow up ts
    bogomips	: 3611.77
    clflush size	: 32
    My systemspecs are:

    OS: Xubuntu 8.04
    Ram: 512MB
    VGA: Ati Radeon 9800pro (latest fglrx)
    CPU: Athlon XP 2200+

    Keep on your great work!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •