ati x700 and dual head

[brennero]

Hi gentlmen,
I'm using a laptop Acer with AMD 64, I've just installed the drivers fglrx from Livna for the Ati x700 video card. I'd like to use it in dual mode, but when I try to set the Ati control panel, plug-in the second monitor and restart both the screen get black.
Here it is my xorg.conf if can be useful

# Xorg configuration created by system-config-display

Section "ServerLayout"
Identifier "single head configuration"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Synaptics" "CorePointer"
EndSection

Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbModel" "pc105"
Option "XkbLayout" "it"
EndSection

Section "InputDevice"
Identifier "Synaptics"
Driver "synaptics"
Option "Device" "/dev/input/mice"
Option "Protocol" "auto-dev"
Option "Emulate3Buttons" "yes"
EndSection

Section "Monitor"

### Comment all HorizSync and VertSync values to use DDC:
### Comment all HorizSync and VertSync values to use DDC:
Identifier "Monitor0"
ModelName "LCD Panel 1280x800"
### Comment all HorizSync and VertSync values to use DDC:
HorizSync 31.5 - 90.0
VertRefresh 59.9 - 60.1
Option "dpms"
EndSection

Section "Device"
Identifier "Videocard0"
Driver "fglrx"
Option "VideoOverlay" "on"
EndSection

Section "Screen"
Identifier "Screen0"
Device "Videocard0"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1024x768" "800x600" "640x480"
EndSubSection
EndSection

Section "ServerFlags"
Option "AIGLX" "off"
EndSection
Section "DRI"
Group 0
Mode 0666
EndSection
Section "Extensions"
Option "Composite" "False"
EndSection
Section "Module"
Load "extmod"
Load "glx"
Load "dri"
EndSection


Thank you for your attention

[yatt]

Hi gentlmen,
I'm using a laptop Acer with AMD 64, I've just installed the drivers fglrx from Livna for the Ati x700 video card. I'd like to use it in dual mode, but when I try to set the Ati control panel, plug-in the second monitor and restart both the screen get black.
Here it is my xorg.conf if can be useful

# Xorg configuration created by system-config-display

Section "ServerLayout"
Identifier "single head configuration"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Synaptics" "CorePointer"
EndSection

Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbModel" "pc105"
Option "XkbLayout" "it"
EndSection

Section "InputDevice"
Identifier "Synaptics"
Driver "synaptics"
Option "Device" "/dev/input/mice"
Option "Protocol" "auto-dev"
Option "Emulate3Buttons" "yes"
EndSection

Section "Monitor"

### Comment all HorizSync and VertSync values to use DDC:
### Comment all HorizSync and VertSync values to use DDC:
Identifier "Monitor0"
ModelName "LCD Panel 1280x800"
### Comment all HorizSync and VertSync values to use DDC:
HorizSync 31.5 - 90.0
VertRefresh 59.9 - 60.1
Option "dpms"
EndSection

Section "Device"
Identifier "Videocard0"
Driver "fglrx"
Option "VideoOverlay" "on"
EndSection

Section "Screen"
Identifier "Screen0"
Device "Videocard0"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1024x768" "800x600" "640x480"
EndSubSection
EndSection

Section "ServerFlags"
Option "AIGLX" "off"
EndSection
Section "DRI"
Group 0
Mode 0666
EndSection
Section "Extensions"
Option "Composite" "False"
EndSection
Section "Module"
Load "extmod"
Load "glx"
Load "dri"
EndSection


Thank you for your attention

Run the command

aticonfig --help

It will list a few commands that you can use to setup your x.org. IIRC, there are two for dual head (ATI calls it big desktop). I typically use the second. I'd look it up myself, but am on a school computer.