Oh I forgot, I'm using latest fglrx driver
first I have ti admit that I'm not that god in english. So be indulgent ;-)
I have a Jetway JNC81-LF witch a radeon hd3200.
When I configured my HTPC (with this Mainboard) in my Office with a FullHD Monitor I had a Slider in amdccc which changed the value of the underscan down to zero.
But after I connected the PC with my Plasma-TV in my living-room there was no slider any more.
The Problem is no, my TV has a fixed Overscan (you can't turn it of) na dthe Underscan of the driver is overcompensating it. So I have a Black Frame around the Desktop.
So I tried several things like :
--> to get some InfoCode:aticonfig --query-monitor Error: option --query-monitor is not supported when RandR 1.2 is enabled!
--> No effect after restarting the X-serverCode:aticonfig --set-pcs-val=MCIL,DigitalHDTVDefaultUnderscan,0 Set key MCIL,DigitalHDTVDefaultUnderscan
--> which led toCode:aticonfig --set-dispattrib=DFP5,positionX:0 aticonfig --set-dispattrib=DFP5,positionY:0 aticonfig --set-dispattrib=DFP5,sizeX:1920 aticonfig --set-dispattrib=DFP5,sizeY:1080
So now I'm stuckCode:Try to Set positionX adjust of monitor DFP5 value : 0 failed. It may not supported by monitor or the value beyond the range. Try to Set positionY adjust of monitor DFP5 value : 0 failed. It may not supported by monitor or the value beyond the range. Try to Set sizeX adjust of monitor DFP5 value : 1920 failed. It may not supported by monitor or the value beyond the range. Try to Set sizeY adjust of monitor DFP5 value : 1080 failed. It may not supported by monitor or the value beyond the range.
What can I do get this Slider back ?
Or do I have to use the radeonhd driver ?
In case yes, what should I write into Xorg.conf to bypass tho overscan of the TV.
BTW : The TV is a HDready Panasonic TH-42PV60EH
Thanks a lot
Oh I forgot, I'm using latest fglrx driver
there must bo someone out there who knows how to configure a radeon card with an overscanning Monitor !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!1
I don't think anyone has ever seen a digital monitor whose overscan can't be turned off. Probably worth going through the manual again - the option usually has a wierd name, like "show all pixels" rather than something useful like "overscan on/off".
Yes, you're right it's 1024x768. But this resolution works only at the vga-input of the TV. If you're using hdmi you're set with the usual HD-resolutions. And because I whant to use my PC as a PVR ....
I can assure that checked every Option bevor. There is NO pssibility to switch Overscan off. Not in the user menu and even not in the service menu. This is only an Optionin the later Models of Panasonic.
But, what would this help. My Problem is the underscan of the fglrx-driver. If I could turn Overscan off, the undescan Problem would even be greater.
The mentioned Slider was my main reason to buy this MB. FRom my understanding fglrx is getting somy information via EDID which leads to turn off this Option.
Is there no way to store the EDID information local, edit something in there which brings back the slider and tell xorg to load the EDID info from there ?
Or second but less good idea. Is there no way to turn underscan off ?
There should be a checkbox to turn off the underscan in CCC-LE; I haven't used it for a while but IIRC there's a tab for TV etc and the checkbox is on that tab.
I'm not sitting in front of the PC.
Isn't this Checkbox available at the same Tab like this Slider ?
As I told, I can't see both of them. Could it be a problem that I moved the PC from Office to living room, so that the config files where created at my office Monitor but it'S now connected to tha Plasma-TV.
Should I probably delete all Config files and run "aticonfig --initial" again ?
Ideally I would not completely turn of the underscan. I just want to reduce the value of it.
Could be s slider these days, not sure.
Yeah, running aticonfig --initial again might help.
The underscan used to be enabled by default when the driver detected an HDMI-connected display running at any of the standard HD TV resolutions, and stayed on until turned off by the user via CCC-LE.
Ok, I'll try that again when I'm back home.
Is there no way to turn this Option on/off in a config file or something ?