Page 1 of 3 123 LastLast
Results 1 to 10 of 22

Thread: problem with Radeon AH 4650 (agp)

  1. #1
    Join Date
    May 2009
    Posts
    8

    Default problem with Radeon AH 4650 (agp)

    Hi!
    i bought a new graphic card to the box I use for the kids, replacing the Radeon 9700 with a Radeon 4650. I really wanted to get a Nvidia due to the driver situation, but as the motherboard (Epox 8k7a) limited me to an AGP-card i went with ATi. I didn'e expect stellar performance but at least i expected it to run. Well it doesn't.

    I have a clean install of Ubuntu Maverick 10.10 on a box with AMD Athlon +2200, 500 mb ram, and an Asus RAdeon AH 4650. When I enable the propriarity drivers and reboot, the system hangs before login. Any clues?

    thanx / Anfanglir

  2. #2
    Join Date
    May 2009
    Posts
    8

    Default

    Here's half the output of dmesg (please advice me of what else to post):

    (Please advice me of what else to post)

    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1
    [ 0.000000] early_res array is doubled to 64 at [16000 - 167ff]
    [ 0.000000] PERCPU: Embedded 14 pages/cpu @c1800000 s36416 r0 d20928 u4194304
    [ 0.000000] pcpu-alloc: s36416 r0 d20928 u4194304 alloc=1*4194304
    [ 0.000000] pcpu-alloc: [0] 0
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129920
    [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.35-22-generic root=UUID=e9ce018e-e87e-49dc-865a-25e6b7d5565e ro single nomodeset
    [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
    [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    [ 0.000000] Enabling fast FPU save and restore... done.
    [ 0.000000] Enabling unmasked SIMD FPU exception support... done.
    [ 0.000000] Initializing CPU#0
    [ 0.000000] allocated 2621100 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] Subtract (38 early reservations)
    [ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE
    [ 0.000000] #2 [0000100000 - 00009a0adc] TEXT DATA BSS
    [ 0.000000] #3 [00175f0000 - 0018034000] RAMDISK
    [ 0.000000] #4 [000009fc00 - 0000100000] BIOS reserved
    [ 0.000000] #5 [00009a1000 - 00009a4076] BRK
    [ 0.000000] #6 [0000010000 - 0000011000] TRAMPOLINE
    [ 0.000000] #7 [0000011000 - 0000015000] ACPI WAKEUP
    [ 0.000000] #8 [0000015000 - 0000016000] PGTABLE
    [ 0.000000] #9 [0001000000 - 0001001000] BOOTMEM
    [ 0.000000] #10 [0001001000 - 0001401000] BOOTMEM
    [ 0.000000] #11 [0001401000 - 0001401004] BOOTMEM
    [ 0.000000] #12 [0001401040 - 0001401100] BOOTMEM
    [ 0.000000] #13 [0001401100 - 0001401130] BOOTMEM
    [ 0.000000] #14 [0001401140 - 0001402940] BOOTMEM
    [ 0.000000] #15 [0001402940 - 0001402a58] BOOTMEM
    [ 0.000000] #16 [0001402a80 - 0001402ac0] BOOTMEM
    [ 0.000000] #17 [0001402ac0 - 0001402b00] BOOTMEM
    [ 0.000000] #18 [0001402b00 - 0001402b40] BOOTMEM
    [ 0.000000] #19 [0001402b40 - 0001402b80] BOOTMEM
    [ 0.000000] #20 [0001402b80 - 0001402bc0] BOOTMEM
    [ 0.000000] #21 [0001402bc0 - 0001402c00] BOOTMEM
    [ 0.000000] #22 [0001402c00 - 0001402c40] BOOTMEM
    [ 0.000000] #23 [0001402c40 - 0001402c50] BOOTMEM
    [ 0.000000] #24 [0001402c80 - 0001402c90] BOOTMEM
    [ 0.000000] #25 [0001402cc0 - 0001402d2e] BOOTMEM
    [ 0.000000] #26 [0001402d40 - 0001402dae] BOOTMEM
    [ 0.000000] #27 [0001800000 - 000180e000] BOOTMEM
    [ 0.000000] #28 [0001404dc0 - 0001404dc4] BOOTMEM
    [ 0.000000] #29 [0001404e00 - 0001404e04] BOOTMEM
    [ 0.000000] #30 [0001404e40 - 0001404e44] BOOTMEM
    [ 0.000000] #31 [0001404e80 - 0001404e84] BOOTMEM
    [ 0.000000] #32 [0001404ec0 - 0001404f70] BOOTMEM
    [ 0.000000] #33 [0001404f80 - 0001405028] BOOTMEM
    [ 0.000000] #34 [0001402dc0 - 0001404dc0] BOOTMEM
    [ 0.000000] #35 [0001405040 - 0001445040] BOOTMEM
    [ 0.000000] #36 [0001445040 - 0001465040] BOOTMEM
    [ 0.000000] #37 [0001466000 - 00016e5eac] BOOTMEM
    [ 0.000000] Initializing HighMem for node 0 (00000000:00000000)
    [ 0.000000] Memory: 497264k/524224k available (4928k kernel code, 26512k reserved, 2336k data, 684k init, 0k highmem)
    [ 0.000000] virtual kernel memory layout:
    [ 0.000000] fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
    [ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    [ 0.000000] vmalloc : 0xe07f0000 - 0xff7fe000 ( 496 MB)
    [ 0.000000] lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
    [ 0.000000] .init : 0xc0819000 - 0xc08c4000 ( 684 kB)
    [ 0.000000] .data : 0xc05d029e - 0xc0818668 (2336 kB)
    [ 0.000000] .text : 0xc0100000 - 0xc05d029e (4928 kB)
    [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
    [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
    [ 0.000000] Hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] RCU-based detection of stalled CPUs is disabled.
    [ 0.000000] Verbose stalled-CPUs detection is disabled.
    [ 0.000000] NR_IRQS:2304 nr_irqs:256
    [ 0.000000] Console: colour VGA+ 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] Fast TSC calibration using PIT
    [ 0.000000] Detected 1794.670 MHz processor.
    [ 0.008006] Calibrating delay loop (skipped), value calculated using timer frequency.. 3589.34 BogoMIPS (lpj=7178680)
    [ 0.008111] pid_max: default: 32768 minimum: 301
    [ 0.008205] Security Framework initialized
    [ 0.008295] AppArmor: AppArmor initialized
    [ 0.008344] Yama: becoming mindful.
    [ 0.008489] Mount-cache hash table entries: 512
    [ 0.008768] Initializing cgroup subsys ns
    [ 0.008821] Initializing cgroup subsys cpuacct
    [ 0.008875] Initializing cgroup subsys memory
    [ 0.008935] Initializing cgroup subsys devices
    [ 0.008987] Initializing cgroup subsys freezer
    [ 0.009037] Initializing cgroup subsys net_cls
    [ 0.009130] mce: CPU supports 4 MCE banks
    [ 0.009206] Performance Events:
    [ 0.009249] no APIC, boot with the "lapic" boot parameter to force-enable it.
    [ 0.009343] no hardware sampling interrupt available.
    [ 0.009393] AMD PMU driver.
    [ 0.009455] ... version: 0
    [ 0.009503] ... bit width: 48
    [ 0.009551] ... generic registers: 4
    [ 0.009600] ... value mask: 0000ffffffffffff
    [ 0.009652] ... max period: 00007fffffffffff
    [ 0.009703] ... fixed-purpose events: 0
    [ 0.009752] ... event mask: 000000000000000f
    [ 0.010729] SMP alternatives: switching to UP code
    [ 0.020992] Freeing SMP alternatives: 24k freed
    [ 0.021101] ACPI: Core revision 20100428
    [ 0.027278] ACPI: setting ELCR to 0200 (from 0e20)
    [ 0.028125] ftrace: converting mcount calls to 0f 1f 44 00 00
    [ 0.028187] ftrace: allocating 21758 entries in 43 pages
    [ 0.032186] weird, boot CPU (#0) not listed by the BIOS.
    [ 0.032244] SMP motherboard not detected.
    [ 0.032293] Local APIC not detected. Using dummy APIC emulation.
    [ 0.032344] SMP disabled
    [ 0.032868] Brought up 1 CPUs
    [ 0.032915] Total of 1 processors activated (3589.34 BogoMIPS).
    [ 0.033721] devtmpfs: initialized
    [ 0.036635] regulator: core version 0.5
    [ 0.036722] Time: 19:21:58 Date: 12/20/10
    [ 0.036829] NET: Registered protocol family 16
    [ 0.037080] EISA bus registered
    [ 0.037145] ACPI: bus type pci registered
    [ 0.068703] PCI: PCI BIOS revision 2.10 entry at 0xfb680, last bus=1
    [ 0.068756] PCI: Using configuration type 1 for base access
    [ 0.070235] bio: create slab <bio-0> at 0
    [ 0.071071] ACPI: EC: Look up EC in DSDT
    [ 0.074969] ACPI: Interpreter enabled
    [ 0.075021] ACPI: (supports S0 S1 S4 S5)
    [ 0.075226] ACPI: Using PIC for interrupt routing
    [ 0.079797] ACPI: No dock devices found.
    [ 0.079850] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
    [ 0.080106] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    [ 0.080469] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
    [ 0.080474] pci_root PNP0A03:00: host bridge window [io 0x0d00-0x3fff] (ignored)
    [ 0.080478] pci_root PNP0A03:00: host bridge window [io 0x4100-0x4fff] (ignored)
    [ 0.080481] pci_root PNP0A03:00: host bridge window [io 0x5010-0x5fff] (ignored)
    [ 0.080485] pci_root PNP0A03:00: host bridge window [io 0x6080-0xffff] (ignored)
    [ 0.080489] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
    [ 0.080493] pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000dffff] (ignored)
    [ 0.080496] pci_root PNP0A03:00: host bridge window [mem 0x20000000-0xffefffff] (ignored)
    [ 0.080526] pci 0000:00:00.0: reg 10: [mem 0xe0000000-0xe7ffffff pref]
    [ 0.080532] pci 0000:00:00.0: reg 14: [mem 0xea000000-0xea000fff pref]
    [ 0.080539] pci 0000:00:00.0: reg 18: [io 0xa000-0xa003]
    [ 0.080689] pci 0000:00:07.1: reg 20: [io 0xa400-0xa40f]
    [ 0.080747] pci 0000:00:07.2: reg 20: [io 0xa800-0xa81f]
    [ 0.080805] pci 0000:00:07.3: reg 20: [io 0xac00-0xac1f]
    [ 0.080878] pci 0000:00:07.4: quirk: [io 0x6000-0x607f] claimed by vt82c686 HW-mon
    [ 0.080941] pci 0000:00:07.4: quirk: [io 0x5000-0x500f] claimed by vt82c686 SMB
    [ 0.081035] pci 0000:00:07.5: reg 10: [io 0xb000-0xb0ff]
    [ 0.081042] pci 0000:00:07.5: reg 14: [io 0xb400-0xb403]
    [ 0.081048] pci 0000:00:07.5: reg 18: [io 0xb800-0xb803]
    [ 0.081104] pci 0000:00:0a.0: reg 10: [mem 0xea001000-0xea0017ff]
    [ 0.081111] pci 0000:00:0a.0: reg 14: [io 0xbc00-0xbc7f]
    [ 0.081143] pci 0000:00:0a.0: supports D2
    [ 0.081146] pci 0000:00:0a.0: PME# supported from D2 D3hot D3cold
    [ 0.081151] pci 0000:00:0a.0: PME# disabled
    [ 0.081175] pci 0000:00:0d.0: reg 10: [io 0xc000-0xc01f]
    [ 0.081260] pci 0000:01:05.0: reg 10: [mem 0xd0000000-0xdfffffff pref]
    [ 0.081267] pci 0000:01:05.0: reg 14: [io 0x9000-0x90ff]
    [ 0.081275] pci 0000:01:05.0: reg 18: [mem 0xe9000000-0xe900ffff]
    [ 0.081293] pci 0000:01:05.0: reg 30: [mem 0x00000000-0x0001ffff pref]
    [ 0.081316] pci 0000:01:05.0: supports D1 D2
    [ 0.081349] pci 0000:01:05.1: reg 10: [mem 0xe9010000-0xe9013fff]
    [ 0.081390] pci 0000:01:05.1: supports D1 D2
    [ 0.081422] pci 0000:00:01.0: PCI bridge to [bus 01-01]
    [ 0.082823] pci 0000:00:01.0: bridge window [io 0x9000-0x9fff]
    [ 0.082828] pci 0000:00:01.0: bridge window [mem 0xe8000000-0xe9ffffff]
    [ 0.082833] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff pref]
    [ 0.082841] pci_bus 0000:00: on NUMA node 0
    [ 0.082847] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    [ 0.096817] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
    [ 0.097501] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
    [ 0.098186] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
    [ 0.098871] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
    [ 0.099409] HEST: Table is not found!
    [ 0.099598] vgaarb: device added: PCI:0000:01:05.0,decodes=io+mem,owns=io+mem,locks= none
    [ 0.099661] vgaarb: loaded
    [ 0.099985] SCSI subsystem initialized
    [ 0.100148] libata version 3.00 loaded.
    [ 0.100237] usbcore: registered new interface driver usbfs
    [ 0.100303] usbcore: registered new interface driver hub
    [ 0.100401] usbcore: registered new device driver usb
    [ 0.100704] ACPI: WMI: Mapper loaded
    [ 0.100752] PCI: Using ACPI for IRQ routing
    [ 0.100804] PCI: pci_cache_line_size set to 32 bytes
    [ 0.100863] reserve RAM buffer: 0000000000002000 - 000000000000ffff
    [ 0.100868] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
    [ 0.100871] reserve RAM buffer: 000000001fff0000 - 000000001fffffff
    [ 0.101034] NetLabel: Initializing
    [ 0.101082] NetLabel: domain hash size = 128
    [ 0.101129] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.101199] NetLabel: unlabeled traffic allowed by default
    [ 0.101329] Switching to clocksource tsc
    [ 0.116969] AppArmor: AppArmor Filesystem Enabled
    [ 0.117062] pnp: PnP ACPI init
    [ 0.117145] ACPI: bus type pnp registered
    [ 0.118283] ERROR: Unable to locate IOAPIC for GSI 8
    [ 0.118426] ERROR: Unable to locate IOAPIC for GSI 13
    [ 0.118728] ERROR: Unable to locate IOAPIC for GSI 6
    [ 0.119201] ERROR: Unable to locate IOAPIC for GSI 4
    [ 0.119707] ERROR: Unable to locate IOAPIC for GSI 3
    [ 0.120621] ERROR: Unable to locate IOAPIC for GSI 7
    [ 0.120812] ERROR: Unable to locate IOAPIC for GSI 1
    [ 0.120900] pnp: PnP ACPI: found 12 devices
    [ 0.120949] ACPI: ACPI bus type pnp unregistered
    [ 0.121000] PnPBIOS: Disabled by ACPI PNP
    [ 0.121068] system 00:00: [mem 0x000d0000-0x000d3fff] has been reserved
    [ 0.121122] system 00:00: [mem 0x000f0000-0x000f7fff] could not be reserved
    [ 0.121176] system 00:00: [mem 0x000f8000-0x000fbfff] could not be reserved
    [ 0.121230] system 00:00: [mem 0x000fc000-0x000fffff] could not be reserved
    [ 0.121284] system 00:00: [mem 0x1fff0000-0x1fffffff] could not be reserved
    [ 0.121338] system 00:00: [mem 0xffff0000-0xffffffff] has been reserved
    [ 0.121391] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
    [ 0.121445] system 00:00: [mem 0x00100000-0x1ffeffff] could not be reserved
    [ 0.121499] system 00:00: [mem 0xfee00000-0xfee00fff] has been reserved
    [ 0.121558] system 00:02: [io 0x04d0-0x04d1] has been reserved
    [ 0.158437] pci 0000:01:05.0: BAR 6: assigned [mem 0xe8000000-0xe801ffff pref]
    [ 0.158503] pci 0000:00:01.0: PCI bridge to [bus 01-01]
    [ 0.158555] pci 0000:00:01.0: bridge window [io 0x9000-0x9fff]
    [ 0.158625] pci 0000:00:01.0: bridge window [mem 0xe8000000-0xe9ffffff]
    [ 0.158679] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff pref]
    [ 0.158751] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
    [ 0.158754] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
    [ 0.158759] pci_bus 0000:01: resource 0 [io 0x9000-0x9fff]
    [ 0.158762] pci_bus 0000:01: resource 1 [mem 0xe8000000-0xe9ffffff]
    [ 0.158766] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff pref]
    [ 0.158849] NET: Registered protocol family 2
    [ 0.158998] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
    [ 0.159357] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
    [ 0.159715] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
    [ 0.160048] TCP: Hash tables configured (established 16384 bind 16384)
    [ 0.160100] TCP reno registered
    [ 0.160149] UDP hash table entries: 256 (order: 1, 8192 bytes)
    [ 0.160215] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
    [ 0.160417] NET: Registered protocol family 1
    [ 0.160495] pci 0000:00:07.0: Disabling VIA external APIC routing
    [ 0.160593] pci 0000:01:05.0: Boot video device
    [ 0.160601] PCI: CLS 32 bytes, default 32
    [ 0.161010] cpufreq-nforce2: No nForce2 chipset.
    [ 0.161098] Scanning for low memory corruption every 60 seconds
    [ 0.161446] audit: initializing netlink socket (disabled)
    [ 0.161516] type=2000 audit(1292872918.156:1): initialized
    [ 0.173831] Trying to unpack rootfs image as initramfs...
    [ 0.187413] HugeTLB registered 4 MB page size, pre-allocated 0 pages
    [ 0.199069] VFS: Disk quotas dquot_6.5.2
    [ 0.199313] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    [ 0.200309] fuse init (API version 7.14)
    [ 0.200499] msgmni has been set to 971
    [ 0.207517] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
    [ 0.207587] io scheduler noop registered
    [ 0.207635] io scheduler deadline registered
    [ 0.207697] io scheduler cfq registered (default)
    [ 0.207929] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [ 0.208013] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
    [ 0.208344] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
    [ 0.208414] ACPI: Power Button [PWRB]
    [ 0.208540] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1

    lovidar@lovidar:~$

  3. #3
    Join Date
    May 2009
    Posts
    8

    Default

    and here'e the rest of dmesg:

    [ 0.208603] ACPI: Power Button [PWRF]
    [ 0.208715] ACPI: Fan [FAN] (on)
    [ 0.208965] ACPI: acpi_idle registered with cpuidle
    [ 0.211383] thermal LNXTHERM:01: registered as thermal_zone0
    [ 0.211444] ACPI: Thermal Zone [THRM] (32 C)
    [ 0.211556] ERST: Table is not found!
    [ 0.211958] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
    [ 0.212172] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    [ 0.212353] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    [ 0.212791] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    [ 0.213010] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    [ 0.218731] isapnp: Scanning for PnP cards...
    [ 0.224644] brd: module loaded
    [ 0.225541] loop: module loaded
    [ 0.230831] Fixed MDIO Bus: probed
    [ 0.230948] PPP generic driver version 2.4.2
    [ 0.231134] tun: Universal TUN/TAP device driver, 1.6
    [ 0.231185] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
    [ 0.231398] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 0.231491] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [ 0.231559] uhci_hcd: USB Universal Host Controller Interface driver
    [ 0.232389] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
    [ 0.232442] PCI: setting IRQ 11 as level-triggered
    [ 0.232451] uhci_hcd 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
    [ 0.232528] uhci_hcd 0000:00:07.2: UHCI Host Controller
    [ 0.232632] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
    [ 0.232728] uhci_hcd 0000:00:07.2: irq 11, io base 0x0000a800
    [ 0.233013] hub 1-0:1.0: USB hub found
    [ 0.233068] hub 1-0:1.0: 2 ports detected
    [ 0.233196] uhci_hcd 0000:00:07.3: PCI INT D -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
    [ 0.233264] uhci_hcd 0000:00:07.3: UHCI Host Controller
    [ 0.233372] uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
    [ 0.233451] uhci_hcd 0000:00:07.3: irq 11, io base 0x0000ac00
    [ 0.233678] hub 2-0:1.0: USB hub found
    [ 0.233730] hub 2-0:1.0: 2 ports detected
    [ 0.233919] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
    [ 0.233972] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
    [ 0.234178] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 0.277984] mice: PS/2 mouse device common for all mice
    [ 0.278230] rtc_cmos 00:04: RTC can wake from S4
    [ 0.278344] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
    [ 0.278422] rtc0: alarms up to one year, y3k, 242 bytes nvram
    [ 0.278679] device-mapper: uevent: version 1.0.3
    [ 0.282528] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com
    [ 0.286050] device-mapper: multipath: version 1.1.1 loaded
    [ 0.286116] device-mapper: multipath round-robin: version 1.0.0 loaded
    [ 0.290916] EISA: Probing bus 0 at eisa.0
    [ 0.291001] Cannot allocate resource for EISA slot 4
    [ 0.291052] Cannot allocate resource for EISA slot 5
    [ 0.291101] Cannot allocate resource for EISA slot 6
    [ 0.291176] EISA: Detected 0 cards.
    [ 0.294006] cpuidle: using governor ladder
    [ 0.294064] cpuidle: using governor menu
    [ 0.294577] TCP cubic registered
    [ 0.294916] NET: Registered protocol family 10
    [ 0.295442] lo: Disabled Privacy Extensions
    [ 0.295759] NET: Registered protocol family 17
    [ 0.295875] powernow-k8: Processor cpuid 680 not supported
    [ 0.295958] Using IPI No-Shortcut mode
    [ 0.296180] PM: Resume from disk failed.
    [ 0.296212] registered taskstats version 1
    [ 0.296467] Magic number: 6:379:395
    [ 0.296605] pci 0000:00:07.0: hash matches
    [ 0.296753] rtc_cmos 00:04: setting system clock to 2010-12-20 19:21:58 UTC (1292872918)
    [ 0.296815] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
    [ 0.296867] EDD information not available.
    [ 0.297022] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
    [ 0.634457] usb 1-1: new low speed USB device using uhci_hcd and address 2
    [ 0.894604] isapnp: No Plug & Play device found
    [ 0.956089] Freeing initrd memory: 10512k freed
    [ 0.976822] Freeing unused kernel memory: 684k freed
    [ 0.978308] Write protecting the kernel text: 4932k
    [ 0.978399] Write protecting the kernel read-only data: 1976k
    [ 1.014813] udev[63]: starting version 163
    [ 1.030828] usb 1-2: new full speed USB device using uhci_hcd and address 3
    [ 1.294681] pata_via 0000:00:07.1: version 0.3.4
    [ 1.334484] ne2k-pci.c:v1.03 9/22/2003 D. Becker/P. Gortmaker
    [ 1.336189] scsi0 : pata_via
    [ 1.347604] Floppy drive(s): fd0 is 1.44M
    [ 1.370587] scsi1 : pata_via
    [ 1.372951] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xa400 irq 14
    [ 1.373008] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xa408 irq 15
    [ 1.377072] FDC 0 is a post-1991 82077
    [ 1.377183] ne2k-pci 0000:00:0d.0: PCI INT A -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
    [ 1.379315] eth0: RealTek RTL-8029 found at 0xc000, IRQ 11, 00:00:1c:09:b4:5c.
    [ 1.544630] ata1.00: ATA-6: HDS722512VLAT80, V33OA60A, max UDMA/100
    [ 1.544693] ata1.00: 241254720 sectors, multi 16: LBA48
    [ 1.568631] ata1.00: configured for UDMA/100
    [ 1.568893] scsi 0:0:0:0: Direct-Access ATA HDS722512VLAT80 V33O PQ: 0 ANSI: 5
    [ 1.569273] sd 0:0:0:0: Attached scsi generic sg0 type 0
    [ 1.569916] sd 0:0:0:0: [sda] 241254720 512-byte logical blocks: (123 GB/115 GiB)
    [ 1.570068] sd 0:0:0:0: [sda] Write Protect is off
    [ 1.570119] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 1.570158] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 1.570478] sda: sda1 sda2 < sda5 sda6 sda7 >
    [ 1.608783] sd 0:0:0:0: [sda] Attached SCSI disk
    [ 1.732361] ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-H10A, JL02, max UDMA/33
    [ 1.748364] ata2.00: configured for UDMA/33
    [ 1.754067] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-H10A JL02 PQ: 0 ANSI: 5
    [ 1.766846] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
    [ 1.766920] Uniform CD-ROM driver Revision: 3.20
    [ 1.767712] sr 1:0:0:0: Attached scsi CD-ROM sr0
    [ 1.767952] sr 1:0:0:0: Attached scsi generic sg1 type 5
    [ 1.771972] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
    [ 1.772098] PCI: setting IRQ 5 as level-triggered
    [ 1.772106] firewire_ohci 0000:00:0a.0: PCI INT A -> Link[LNKC] -> GSI 5 (level, low) -> IRQ 5
    [ 1.795452] usbcore: registered new interface driver hiddev
    [ 1.808847] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:07.2/usb1/1-1/1-1:1.0/input/input3
    [ 1.809426] generic-usb 0003:046D:C00E.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:07.2-1/input0
    [ 1.809922] usbcore: registered new interface driver usbhid
    [ 1.809978] usbhid: USB HID core driver
    [ 1.880048] firewire_ohci: Added fw-ohci device 0000:00:0a.0, OHCI v1.0, 8 IR + 8 IT contexts, quirks 0x1
    [ 2.372265] firewire_core: created device fw0: GUID 0011060000003669, S400
    [ 2.476170] EXT4-fs (sda6): INFO: recovery required on readonly filesystem
    [ 2.476304] EXT4-fs (sda6): write access will be enabled during recovery
    [ 2.571863] EXT4-fs (sda6): recovery complete
    [ 2.601788] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
    [ 4.551088] Adding 6373372k swap on /dev/sda5. Priority:-1 extents:1 across:6373372k
    [ 5.428518] udev[291]: starting version 163
    [ 6.423709] cfg80211: Calling CRDA to update world regulatory domain
    [ 6.478582] parport_pc: VIA 686A/8231 detected
    [ 6.478592] parport_pc: probing current configuration
    [ 6.478611] parport_pc: Current parallel port base: 0x378
    [ 6.478687] parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
    [ 6.537136] lp: driver loaded but no devices found
    [ 6.576282] lp0: using parport0 (interrupt-driven).
    [ 6.576288] parport_pc: VIA parallel port: io=0x378, irq=7
    [ 6.617925] ACPI: resource vt596_smbus [io 0x5000-0x5007] conflicts with ACPI region SM06 [??? 0x00005006 flags 0x36]
    [ 6.617933] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 6.704855] ACPI: resource via686a [io 0x6000-0x607f] conflicts with ACPI region IP3_ [??? 0x0000603a flags 0x5f]
    [ 6.704862] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 6.940070] ppdev: user-space parallel port driver
    [ 7.128536] shpchp 0000:00:01.0: HPC vendor_id 1022 device_id 700f ss_vid 0 ss_did 0
    [ 7.128548] shpchp 0000:00:01.0: Cannot reserve MMIO region
    [ 7.130144] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    [ 7.148379] Linux agpgart interface v0.103
    [ 7.197308] agpgart-amdk7 0000:00:00.0: AMD 761 chipset
    [ 7.228513] agpgart-amdk7 0000:00:00.0: AGP aperture is 128M @ 0xe0000000
    [ 7.709745] type=1400 audit(1292872925.909:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient3" pid=469 comm="apparmor_parser"
    [ 7.710143] type=1400 audit(1292872925.909:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=469 comm="apparmor_parser"
    [ 7.710370] type=1400 audit(1292872925.909:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=469 comm="apparmor_parser"
    [ 7.995800] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
    [ 7.995808] Disabling lock debugging due to kernel taint
    [ 8.219676] [fglrx] Maximum main memory to use for locked dma buffers: 425 MBytes.
    [ 8.219816] [fglrx] vendor: 1002 device: 9495 count: 1
    [ 8.220080] [fglrx] ioport: bar 1, base 0x9000, size: 0x100
    [ 8.220662] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
    [ 8.220668] PCI: setting IRQ 10 as level-triggered
    [ 8.220677] pci 0000:01:05.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, low) -> IRQ 10
    [ 8.220849] [fglrx] Kernel PAT support is enabled
    [ 8.220895] [fglrx] module loaded - fglrx 8.78.30 [Sep 20 2010] with 1 minors
    [ 8.266856] cfg80211: World regulatory domain updated:
    [ 8.266864] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    [ 8.266869] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [ 8.266873] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    [ 8.266877] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    [ 8.266880] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [ 8.266884] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [ 8.655700] phy0: Selected rate control algorithm 'minstrel'
    [ 8.656721] Registered led device: rt73usb-phy0::radio
    [ 8.656749] Registered led device: rt73usb-phy0::assoc
    [ 8.656774] Registered led device: rt73usb-phy0::quality
    [ 8.662409] usbcore: registered new interface driver rt73usb
    [ 9.302058] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
    [ 9.302069] HDA Intel 0000:01:05.1: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
    [ 9.889699] VIA 82xx Audio 0000:00:07.5: PCI INT C -> Link[LNKC] -> GSI 5 (level, low) -> IRQ 5
    [ 9.889846] VIA 82xx Audio 0000:00:07.5: setting latency timer to 64
    [ 10.658203] EXT4-fs (sda6): re-mounted. Opts: errors=remount-ro
    [ 12.104287] type=1400 audit(1292872930.305:5): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=797 comm="apparmor_parser"
    [ 12.107541] type=1400 audit(1292872930.305:6): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient3" pid=806 comm="apparmor_parser"
    [ 12.107984] type=1400 audit(1292872930.305:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=806 comm="apparmor_parser"
    [ 12.108818] type=1400 audit(1292872930.309:8): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=806 comm="apparmor_parser"
    [ 12.271903] type=1400 audit(1292872930.469:9): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=807 comm="apparmor_parser"
    [ 12.278670] type=1400 audit(1292872930.477:10): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer" pid=807 comm="apparmor_parser"
    [ 12.283163] type=1400 audit(1292872930.481:11): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=807 comm="apparmor_parser"
    [ 13.833384] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 24.456039] eth0: no IPv6 routers present
    [ 49.393186] hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.
    [ 50.424253] EXT4-fs (sda6): re-mounted. Opts: errors=remount-ro,commit=0

  4. #4
    Join Date
    Oct 2010
    Posts
    257

    Default

    Can you post me an output of "cat /boot/grub/menu.lst"?

    It seems your kernel is booting into "single" mode, reading your dmesg output:

    Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.35-22-generic root=UUID=e9ce018e-e87e-49dc-865a-25e6b7d5565e ro single nomodeset
    If so, change your menu.lst file (if you're in stuck in the console, type "sudo nano /boot/grub/menu.lst" without the quotes) and delete the "single" line.

    The rest seems to be ok...

    Cheers

  5. #5
    Join Date
    Oct 2010
    Posts
    257

    Default

    p.s. Alternatively, edit your boot.cfg file graphically with your Ubuntu live cd / pen drive...

  6. #6
    Join Date
    May 2009
    Posts
    8

    Default

    Thanx
    I use grub 2, here is the content of /edtc/default/grub:

    # If you change this file, run 'update-grub' afterwards to update
    # /boot/grub/grub.cfg.

    GRUB_DEFAULT=0
    #GRUB_HIDDEN_TIMEOUT=0
    GRUB_HIDDEN_TIMEOUT_QUIET=true
    GRUB_TIMEOUT=10
    GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian`
    GRUB_CMDLINE_LINUX_DEFAULT="quiet splash"
    GRUB_CMDLINE_LINUX="nomodeset"

    # Uncomment to enable BadRAM filtering, modify to suit your needs
    # This works with Linux (no patch required) and with any kernel that obtains
    # the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...)
    #GRUB_BADRAM="0x01234567,0xfefefefe,0x89abcdef,0xe fefefef"

    # Uncomment to disable graphical terminal (grub-pc only)
    #GRUB_TERMINAL=console

    # The resolution used on graphical terminal
    # note that you can use only modes which your graphic card supports via VBE
    # you can see them in real GRUB with the command `vbeinfo'
    #GRUB_GFXMODE=640x480

    # Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux
    #GRUB_DISABLE_LINUX_UUID=true

    # Uncomment to disable generation of recovery mode menu entries
    #GRUB_DISABLE_LINUX_RECOVERY="true"

    # Uncomment to get a beep at grub start
    #GRUB_INIT_TUNE="480 440 1"


    I added the "nomodeset" part to disable KMS, i googled this as a possible solution to ATi problems, it didnt't help so I have now removed the "nomodeset" again.

    The xorg.conf look like this:

    Section "Monitor"
    Identifier "aticonfig-Monitor[0]-0"
    Option "VendorName" "ATI Proprietary Driver"
    Option "ModelName" "Generic Autodetecting Monitor"
    Option "DPMS" "true"
    EndSection

    Section "Screen"
    Identifier "aticonfig-Screen[0]-0"
    Device "aticonfig-Device[0]-0"
    Monitor "aticonfig-Monitor[0]-0"
    DefaultDepth 24
    SubSection "Display"
    Viewport 0 0
    Depth 24
    EndSubSection
    EndSection

    Section "Module"
    Load "glx"
    EndSection

    Section "ServerLayout"
    Identifier "aticonfig Layout"
    Screen 0 "aticonfig-Screen[0]-0" 0 0
    EndSection

    Section "Device"
    Identifier "aticonfig-Device[0]-0"
    BusID "PCI:1:5:0"
    Driver "fglrx"
    EndSection


    / Anfanglir

  7. #7
    Join Date
    Oct 2010
    Posts
    257

    Default

    1. You have to disable kernel modesetting (the "nomodeset" line was OK), or then, you'll have lots of trouble with Catalyst...

    2. It's not the /etc/default/grub file that I was talking to you (it's the /boot/grub/menu.lst one)... /etc/default/grub is going to generate you a "default" grub file when you, for instance, update you kernel...

    Cheers

  8. #8
    Join Date
    May 2009
    Posts
    8

    Default

    Quote Originally Posted by evolution View Post
    1. You have to disable kernel modesetting (the "nomodeset" line was OK), or then, you'll have lots of trouble with Catalyst...

    2. It's not the /etc/default/grub file that I was talking to you (it's the /boot/grub/menu.lst one)... /etc/default/grub is going to generate you a "default" grub file when you, for instance, update you kernel...

    Cheers

    OK, thanx

    There is no menu.lst though with Grub2, but there is a grub.cfg in that directory, could that be it:

    #
    # DO NOT EDIT THIS FILE
    #
    # It is automatically generated by grub-mkconfig using templates
    # from /etc/grub.d and settings from /etc/default/grub
    #

    ### BEGIN /etc/grub.d/00_header ###
    if [ -s $prefix/grubenv ]; then
    set have_grubenv=true
    load_env
    fi
    set default="0"
    if [ "${prev_saved_entry}" ]; then
    set saved_entry="${prev_saved_entry}"
    save_env saved_entry
    set prev_saved_entry=
    save_env prev_saved_entry
    set boot_once=true
    fi

    function savedefault {
    if [ -z "${boot_once}" ]; then
    saved_entry="${chosen}"
    save_env saved_entry
    fi
    }

    function recordfail {
    set recordfail=1
    if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi
    }

    function load_video {
    insmod vbe
    insmod vga
    }

    insmod part_msdos
    insmod ext2
    set root='(hd0,msdos6)'
    search --no-floppy --fs-uuid --set e9ce018e-e87e-49dc-865a-25e6b7d5565e
    if loadfont /usr/share/grub/unicode.pf2 ; then
    set gfxmode=640x480
    load_video
    insmod gfxterm
    fi
    terminal_output gfxterm
    insmod part_msdos
    insmod ext2
    set root='(hd0,msdos6)'
    search --no-floppy --fs-uuid --set e9ce018e-e87e-49dc-865a-25e6b7d5565e
    set locale_dir=($root)/boot/grub/locale
    set lang=sv
    insmod gettext
    if [ "${recordfail}" = 1 ]; then
    set timeout=-1
    else
    set timeout=10
    fi
    ### END /etc/grub.d/00_header ###

    ### BEGIN /etc/grub.d/05_debian_theme ###
    set menu_color_normal=white/black
    set menu_color_highlight=black/light-gray
    ### END /etc/grub.d/05_debian_theme ###

    ### BEGIN /etc/grub.d/10_linux ###
    menuentry 'Ubuntu, with Linux 2.6.35-22-generic' --class ubuntu --class gnu-linux --class gnu --class os {
    recordfail
    insmod part_msdos
    insmod ext2
    set root='(hd0,msdos6)'
    search --no-floppy --fs-uuid --set e9ce018e-e87e-49dc-865a-25e6b7d5565e
    linux /boot/vmlinuz-2.6.35-22-generic root=UUID=e9ce018e-e87e-49dc-865a-25e6b7d5565e ro quiet splash
    initrd /boot/initrd.img-2.6.35-22-generic
    }
    menuentry 'Ubuntu, with Linux 2.6.35-22-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os {
    recordfail
    insmod part_msdos
    insmod ext2
    set root='(hd0,msdos6)'
    search --no-floppy --fs-uuid --set e9ce018e-e87e-49dc-865a-25e6b7d5565e
    echo 'Loading Linux 2.6.35-22-generic ...'
    linux /boot/vmlinuz-2.6.35-22-generic root=UUID=e9ce018e-e87e-49dc-865a-25e6b7d5565e ro single
    echo 'Loading initial ramdisk ...'
    initrd /boot/initrd.img-2.6.35-22-generic
    }
    ### END /etc/grub.d/10_linux ###

    ### BEGIN /etc/grub.d/20_linux_xen ###
    ### END /etc/grub.d/20_linux_xen ###

    ### BEGIN /etc/grub.d/20_memtest86+ ###
    menuentry "Memory test (memtest86+)" {
    insmod part_msdos
    insmod ext2
    set root='(hd0,msdos6)'
    search --no-floppy --fs-uuid --set e9ce018e-e87e-49dc-865a-25e6b7d5565e
    linux16 /boot/memtest86+.bin
    }
    menuentry "Memory test (memtest86+, serial console 115200)" {
    insmod part_msdos
    insmod ext2
    set root='(hd0,msdos6)'
    search --no-floppy --fs-uuid --set e9ce018e-e87e-49dc-865a-25e6b7d5565e
    linux16 /boot/memtest86+.bin console=ttyS0,115200n8
    }
    ### END /etc/grub.d/20_memtest86+ ###

    ### BEGIN /etc/grub.d/30_os-prober ###
    menuentry "Ubuntu 8.04.4 LTS, kernel 2.6.24-28-generic (on /dev/sda1)" {
    insmod part_msdos
    insmod ext2
    set root='(hd0,msdos1)'
    search --no-floppy --fs-uuid --set 3b12d5c7-5bac-4b2b-a1a0-794c4c22ba48
    linux /boot/vmlinuz-2.6.24-28-generic root=UUID=3b12d5c7-5bac-4b2b-a1a0-794c4c22ba48 ro quiet splash
    initrd /boot/initrd.img-2.6.24-28-generic
    }

    ### END /etc/grub.d/30_os-prober ###

    ### BEGIN /etc/grub.d/40_custom ###
    # This file provides an easy way to add custom menu entries. Simply type the
    # menu entries you want to add after this comment. Be careful not to change
    # the 'exec tail' line above.
    ### END /etc/grub.d/40_custom ###

    ### BEGIN /etc/grub.d/41_custom ###
    if [ -f $prefix/custom.cfg ]; then
    source $prefix/custom.cfg;
    fi
    ### END /etc/grub.d/41_custom ###


    (I edited out a bunch of different kernel versions of 8.04 LTS)

    / Anfanglir

  9. #9
    Join Date
    Feb 2010
    Posts
    519

    Default

    [ 8.220849] [fglrx] Kernel PAT support is enabled
    Wasn't that a picky option on AGP cards? Like you had to add something similar to "nopat" to the kernel boot options...
    Try searching the forums for this, it rings a bell here

  10. #10
    Join Date
    Feb 2010
    Posts
    519

    Default

    *1 minute edit windoooooooooooow...
    1 minute edit windoooooooooow...
    I hope your death will be painfully sloooooooooooow...
    Can you cause me anything but wooooooooooOOOOOOO*cough*OOOEeeeeEee...*

    BTW what does your xorg.conf look like?
    Specs on your PSU?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •