problem with Radeon AH 4650 (agp)

[Anfanglir]

Hi!
i bought a new graphic card to the box I use for the kids, replacing the Radeon 9700 with a Radeon 4650. I really wanted to get a Nvidia due to the driver situation, but as the motherboard (Epox 8k7a) limited me to an AGP-card i went with ATi. I didn'e expect stellar performance but at least i expected it to run. Well it doesn't.

I have a clean install of Ubuntu Maverick 10.10 on a box with AMD Athlon +2200, 500 mb ram, and an Asus RAdeon AH 4650. When I enable the propriarity drivers and reboot, the system hangs before login. Any clues?

thanx / Anfanglir

[Anfanglir]

Here's half the output of dmesg (please advice me of what else to post):

(Please advice me of what else to post)

[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1
[ 0.000000] early_res array is doubled to 64 at [16000 - 167ff]
[ 0.000000] PERCPU: Embedded 14 pages/cpu @c1800000 s36416 r0 d20928 u4194304
[ 0.000000] pcpu-alloc: s36416 r0 d20928 u4194304 alloc=1*4194304
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129920
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.35-22-generic root=UUID=e9ce018e-e87e-49dc-865a-25e6b7d5565e ro single nomodeset
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] allocated 2621100 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Subtract (38 early reservations)
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE
[ 0.000000] #2 [0000100000 - 00009a0adc] TEXT DATA BSS
[ 0.000000] #3 [00175f0000 - 0018034000] RAMDISK
[ 0.000000] #4 [000009fc00 - 0000100000] BIOS reserved
[ 0.000000] #5 [00009a1000 - 00009a4076] BRK
[ 0.000000] #6 [0000010000 - 0000011000] TRAMPOLINE
[ 0.000000] #7 [0000011000 - 0000015000] ACPI WAKEUP
[ 0.000000] #8 [0000015000 - 0000016000] PGTABLE
[ 0.000000] #9 [0001000000 - 0001001000] BOOTMEM
[ 0.000000] #10 [0001001000 - 0001401000] BOOTMEM
[ 0.000000] #11 [0001401000 - 0001401004] BOOTMEM
[ 0.000000] #12 [0001401040 - 0001401100] BOOTMEM
[ 0.000000] #13 [0001401100 - 0001401130] BOOTMEM
[ 0.000000] #14 [0001401140 - 0001402940] BOOTMEM
[ 0.000000] #15 [0001402940 - 0001402a58] BOOTMEM
[ 0.000000] #16 [0001402a80 - 0001402ac0] BOOTMEM
[ 0.000000] #17 [0001402ac0 - 0001402b00] BOOTMEM
[ 0.000000] #18 [0001402b00 - 0001402b40] BOOTMEM
[ 0.000000] #19 [0001402b40 - 0001402b80] BOOTMEM
[ 0.000000] #20 [0001402b80 - 0001402bc0] BOOTMEM
[ 0.000000] #21 [0001402bc0 - 0001402c00] BOOTMEM
[ 0.000000] #22 [0001402c00 - 0001402c40] BOOTMEM
[ 0.000000] #23 [0001402c40 - 0001402c50] BOOTMEM
[ 0.000000] #24 [0001402c80 - 0001402c90] BOOTMEM
[ 0.000000] #25 [0001402cc0 - 0001402d2e] BOOTMEM
[ 0.000000] #26 [0001402d40 - 0001402dae] BOOTMEM
[ 0.000000] #27 [0001800000 - 000180e000] BOOTMEM
[ 0.000000] #28 [0001404dc0 - 0001404dc4] BOOTMEM
[ 0.000000] #29 [0001404e00 - 0001404e04] BOOTMEM
[ 0.000000] #30 [0001404e40 - 0001404e44] BOOTMEM
[ 0.000000] #31 [0001404e80 - 0001404e84] BOOTMEM
[ 0.000000] #32 [0001404ec0 - 0001404f70] BOOTMEM
[ 0.000000] #33 [0001404f80 - 0001405028] BOOTMEM
[ 0.000000] #34 [0001402dc0 - 0001404dc0] BOOTMEM
[ 0.000000] #35 [0001405040 - 0001445040] BOOTMEM
[ 0.000000] #36 [0001445040 - 0001465040] BOOTMEM
[ 0.000000] #37 [0001466000 - 00016e5eac] BOOTMEM
[ 0.000000] Initializing HighMem for node 0 (00000000:00000000)
[ 0.000000] Memory: 497264k/524224k available (4928k kernel code, 26512k reserved, 2336k data, 684k init, 0k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xe07f0000 - 0xff7fe000 ( 496 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
[ 0.000000] .init : 0xc0819000 - 0xc08c4000 ( 684 kB)
[ 0.000000] .data : 0xc05d029e - 0xc0818668 (2336 kB)
[ 0.000000] .text : 0xc0100000 - 0xc05d029e (4928 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:2304 nr_irqs:256
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1794.670 MHz processor.
[ 0.008006] Calibrating delay loop (skipped), value calculated using timer frequency.. 3589.34 BogoMIPS (lpj=7178680)
[ 0.008111] pid_max: default: 32768 minimum: 301
[ 0.008205] Security Framework initialized
[ 0.008295] AppArmor: AppArmor initialized
[ 0.008344] Yama: becoming mindful.
[ 0.008489] Mount-cache hash table entries: 512
[ 0.008768] Initializing cgroup subsys ns
[ 0.008821] Initializing cgroup subsys cpuacct
[ 0.008875] Initializing cgroup subsys memory
[ 0.008935] Initializing cgroup subsys devices
[ 0.008987] Initializing cgroup subsys freezer
[ 0.009037] Initializing cgroup subsys net_cls
[ 0.009130] mce: CPU supports 4 MCE banks
[ 0.009206] Performance Events:
[ 0.009249] no APIC, boot with the "lapic" boot parameter to force-enable it.
[ 0.009343] no hardware sampling interrupt available.
[ 0.009393] AMD PMU driver.
[ 0.009455] ... version: 0
[ 0.009503] ... bit width: 48
[ 0.009551] ... generic registers: 4
[ 0.009600] ... value mask: 0000ffffffffffff
[ 0.009652] ... max period: 00007fffffffffff
[ 0.009703] ... fixed-purpose events: 0
[ 0.009752] ... event mask: 000000000000000f
[ 0.010729] SMP alternatives: switching to UP code
[ 0.020992] Freeing SMP alternatives: 24k freed
[ 0.021101] ACPI: Core revision 20100428
[ 0.027278] ACPI: setting ELCR to 0200 (from 0e20)
[ 0.028125] ftrace: converting mcount calls to 0f 1f 44 00 00
[ 0.028187] ftrace: allocating 21758 entries in 43 pages
[ 0.032186] weird, boot CPU (#0) not listed by the BIOS.
[ 0.032244] SMP motherboard not detected.
[ 0.032293] Local APIC not detected. Using dummy APIC emulation.
[ 0.032344] SMP disabled
[ 0.032868] Brought up 1 CPUs
[ 0.032915] Total of 1 processors activated (3589.34 BogoMIPS).
[ 0.033721] devtmpfs: initialized
[ 0.036635] regulator: core version 0.5
[ 0.036722] Time: 19:21:58 Date: 12/20/10
[ 0.036829] NET: Registered protocol family 16
[ 0.037080] EISA bus registered
[ 0.037145] ACPI: bus type pci registered
[ 0.068703] PCI: PCI BIOS revision 2.10 entry at 0xfb680, last bus=1
[ 0.068756] PCI: Using configuration type 1 for base access
[ 0.070235] bio: create slab <bio-0> at 0
[ 0.071071] ACPI: EC: Look up EC in DSDT
[ 0.074969] ACPI: Interpreter enabled
[ 0.075021] ACPI: (supports S0 S1 S4 S5)
[ 0.075226] ACPI: Using PIC for interrupt routing
[ 0.079797] ACPI: No dock devices found.
[ 0.079850] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.080106] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.080469] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
[ 0.080474] pci_root PNP0A03:00: host bridge window [io 0x0d00-0x3fff] (ignored)
[ 0.080478] pci_root PNP0A03:00: host bridge window [io 0x4100-0x4fff] (ignored)
[ 0.080481] pci_root PNP0A03:00: host bridge window [io 0x5010-0x5fff] (ignored)
[ 0.080485] pci_root PNP0A03:00: host bridge window [io 0x6080-0xffff] (ignored)
[ 0.080489] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.080493] pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000dffff] (ignored)
[ 0.080496] pci_root PNP0A03:00: host bridge window [mem 0x20000000-0xffefffff] (ignored)
[ 0.080526] pci 0000:00:00.0: reg 10: [mem 0xe0000000-0xe7ffffff pref]
[ 0.080532] pci 0000:00:00.0: reg 14: [mem 0xea000000-0xea000fff pref]
[ 0.080539] pci 0000:00:00.0: reg 18: [io 0xa000-0xa003]
[ 0.080689] pci 0000:00:07.1: reg 20: [io 0xa400-0xa40f]
[ 0.080747] pci 0000:00:07.2: reg 20: [io 0xa800-0xa81f]
[ 0.080805] pci 0000:00:07.3: reg 20: [io 0xac00-0xac1f]
[ 0.080878] pci 0000:00:07.4: quirk: [io 0x6000-0x607f] claimed by vt82c686 HW-mon
[ 0.080941] pci 0000:00:07.4: quirk: [io 0x5000-0x500f] claimed by vt82c686 SMB
[ 0.081035] pci 0000:00:07.5: reg 10: [io 0xb000-0xb0ff]
[ 0.081042] pci 0000:00:07.5: reg 14: [io 0xb400-0xb403]
[ 0.081048] pci 0000:00:07.5: reg 18: [io 0xb800-0xb803]
[ 0.081104] pci 0000:00:0a.0: reg 10: [mem 0xea001000-0xea0017ff]
[ 0.081111] pci 0000:00:0a.0: reg 14: [io 0xbc00-0xbc7f]
[ 0.081143] pci 0000:00:0a.0: supports D2
[ 0.081146] pci 0000:00:0a.0: PME# supported from D2 D3hot D3cold
[ 0.081151] pci 0000:00:0a.0: PME# disabled
[ 0.081175] pci 0000:00:0d.0: reg 10: [io 0xc000-0xc01f]
[ 0.081260] pci 0000:01:05.0: reg 10: [mem 0xd0000000-0xdfffffff pref]
[ 0.081267] pci 0000:01:05.0: reg 14: [io 0x9000-0x90ff]
[ 0.081275] pci 0000:01:05.0: reg 18: [mem 0xe9000000-0xe900ffff]
[ 0.081293] pci 0000:01:05.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[ 0.081316] pci 0000:01:05.0: supports D1 D2
[ 0.081349] pci 0000:01:05.1: reg 10: [mem 0xe9010000-0xe9013fff]
[ 0.081390] pci 0000:01:05.1: supports D1 D2
[ 0.081422] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.082823] pci 0000:00:01.0: bridge window [io 0x9000-0x9fff]
[ 0.082828] pci 0000:00:01.0: bridge window [mem 0xe8000000-0xe9ffffff]
[ 0.082833] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff pref]
[ 0.082841] pci_bus 0000:00: on NUMA node 0
[ 0.082847] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.096817] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
[ 0.097501] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
[ 0.098186] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
[ 0.098871] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
[ 0.099409] HEST: Table is not found!
[ 0.099598] vgaarb: device added: PCI:0000:01:05.0,decodes=io+mem,owns=io+mem,locks= none
[ 0.099661] vgaarb: loaded
[ 0.099985] SCSI subsystem initialized
[ 0.100148] libata version 3.00 loaded.
[ 0.100237] usbcore: registered new interface driver usbfs
[ 0.100303] usbcore: registered new interface driver hub
[ 0.100401] usbcore: registered new device driver usb
[ 0.100704] ACPI: WMI: Mapper loaded
[ 0.100752] PCI: Using ACPI for IRQ routing
[ 0.100804] PCI: pci_cache_line_size set to 32 bytes
[ 0.100863] reserve RAM buffer: 0000000000002000 - 000000000000ffff
[ 0.100868] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[ 0.100871] reserve RAM buffer: 000000001fff0000 - 000000001fffffff
[ 0.101034] NetLabel: Initializing
[ 0.101082] NetLabel: domain hash size = 128
[ 0.101129] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.101199] NetLabel: unlabeled traffic allowed by default
[ 0.101329] Switching to clocksource tsc
[ 0.116969] AppArmor: AppArmor Filesystem Enabled
[ 0.117062] pnp: PnP ACPI init
[ 0.117145] ACPI: bus type pnp registered
[ 0.118283] ERROR: Unable to locate IOAPIC for GSI 8
[ 0.118426] ERROR: Unable to locate IOAPIC for GSI 13
[ 0.118728] ERROR: Unable to locate IOAPIC for GSI 6
[ 0.119201] ERROR: Unable to locate IOAPIC for GSI 4
[ 0.119707] ERROR: Unable to locate IOAPIC for GSI 3
[ 0.120621] ERROR: Unable to locate IOAPIC for GSI 7
[ 0.120812] ERROR: Unable to locate IOAPIC for GSI 1
[ 0.120900] pnp: PnP ACPI: found 12 devices
[ 0.120949] ACPI: ACPI bus type pnp unregistered
[ 0.121000] PnPBIOS: Disabled by ACPI PNP
[ 0.121068] system 00:00: [mem 0x000d0000-0x000d3fff] has been reserved
[ 0.121122] system 00:00: [mem 0x000f0000-0x000f7fff] could not be reserved
[ 0.121176] system 00:00: [mem 0x000f8000-0x000fbfff] could not be reserved
[ 0.121230] system 00:00: [mem 0x000fc000-0x000fffff] could not be reserved
[ 0.121284] system 00:00: [mem 0x1fff0000-0x1fffffff] could not be reserved
[ 0.121338] system 00:00: [mem 0xffff0000-0xffffffff] has been reserved
[ 0.121391] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.121445] system 00:00: [mem 0x00100000-0x1ffeffff] could not be reserved
[ 0.121499] system 00:00: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.121558] system 00:02: [io 0x04d0-0x04d1] has been reserved
[ 0.158437] pci 0000:01:05.0: BAR 6: assigned [mem 0xe8000000-0xe801ffff pref]
[ 0.158503] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.158555] pci 0000:00:01.0: bridge window [io 0x9000-0x9fff]
[ 0.158625] pci 0000:00:01.0: bridge window [mem 0xe8000000-0xe9ffffff]
[ 0.158679] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff pref]
[ 0.158751] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 0.158754] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
[ 0.158759] pci_bus 0000:01: resource 0 [io 0x9000-0x9fff]
[ 0.158762] pci_bus 0000:01: resource 1 [mem 0xe8000000-0xe9ffffff]
[ 0.158766] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff pref]
[ 0.158849] NET: Registered protocol family 2
[ 0.158998] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.159357] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.159715] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.160048] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.160100] TCP reno registered
[ 0.160149] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.160215] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.160417] NET: Registered protocol family 1
[ 0.160495] pci 0000:00:07.0: Disabling VIA external APIC routing
[ 0.160593] pci 0000:01:05.0: Boot video device
[ 0.160601] PCI: CLS 32 bytes, default 32
[ 0.161010] cpufreq-nforce2: No nForce2 chipset.
[ 0.161098] Scanning for low memory corruption every 60 seconds
[ 0.161446] audit: initializing netlink socket (disabled)
[ 0.161516] type=2000 audit(1292872918.156:1): initialized
[ 0.173831] Trying to unpack rootfs image as initramfs...
[ 0.187413] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.199069] VFS: Disk quotas dquot_6.5.2
[ 0.199313] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.200309] fuse init (API version 7.14)
[ 0.200499] msgmni has been set to 971
[ 0.207517] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.207587] io scheduler noop registered
[ 0.207635] io scheduler deadline registered
[ 0.207697] io scheduler cfq registered (default)
[ 0.207929] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.208013] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.208344] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.208414] ACPI: Power Button [PWRB]
[ 0.208540] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1

lovidar@lovidar:~$

[Anfanglir]

and here'e the rest of dmesg:

[ 0.208603] ACPI: Power Button [PWRF]
[ 0.208715] ACPI: Fan [FAN] (on)
[ 0.208965] ACPI: acpi_idle registered with cpuidle
[ 0.211383] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.211444] ACPI: Thermal Zone [THRM] (32 C)
[ 0.211556] ERST: Table is not found!
[ 0.211958] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.212172] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.212353] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 0.212791] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.213010] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 0.218731] isapnp: Scanning for PnP cards...
[ 0.224644] brd: module loaded
[ 0.225541] loop: module loaded
[ 0.230831] Fixed MDIO Bus: probed
[ 0.230948] PPP generic driver version 2.4.2
[ 0.231134] tun: Universal TUN/TAP device driver, 1.6
[ 0.231185] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.231398] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.231491] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.231559] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.232389] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[ 0.232442] PCI: setting IRQ 11 as level-triggered
[ 0.232451] uhci_hcd 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
[ 0.232528] uhci_hcd 0000:00:07.2: UHCI Host Controller
[ 0.232632] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
[ 0.232728] uhci_hcd 0000:00:07.2: irq 11, io base 0x0000a800
[ 0.233013] hub 1-0:1.0: USB hub found
[ 0.233068] hub 1-0:1.0: 2 ports detected
[ 0.233196] uhci_hcd 0000:00:07.3: PCI INT D -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
[ 0.233264] uhci_hcd 0000:00:07.3: UHCI Host Controller
[ 0.233372] uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
[ 0.233451] uhci_hcd 0000:00:07.3: irq 11, io base 0x0000ac00
[ 0.233678] hub 2-0:1.0: USB hub found
[ 0.233730] hub 2-0:1.0: 2 ports detected
[ 0.233919] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 0.233972] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 0.234178] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.277984] mice: PS/2 mouse device common for all mice
[ 0.278230] rtc_cmos 00:04: RTC can wake from S4
[ 0.278344] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 0.278422] rtc0: alarms up to one year, y3k, 242 bytes nvram
[ 0.278679] device-mapper: uevent: version 1.0.3
[ 0.282528] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com
[ 0.286050] device-mapper: multipath: version 1.1.1 loaded
[ 0.286116] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.290916] EISA: Probing bus 0 at eisa.0
[ 0.291001] Cannot allocate resource for EISA slot 4
[ 0.291052] Cannot allocate resource for EISA slot 5
[ 0.291101] Cannot allocate resource for EISA slot 6
[ 0.291176] EISA: Detected 0 cards.
[ 0.294006] cpuidle: using governor ladder
[ 0.294064] cpuidle: using governor menu
[ 0.294577] TCP cubic registered
[ 0.294916] NET: Registered protocol family 10
[ 0.295442] lo: Disabled Privacy Extensions
[ 0.295759] NET: Registered protocol family 17
[ 0.295875] powernow-k8: Processor cpuid 680 not supported
[ 0.295958] Using IPI No-Shortcut mode
[ 0.296180] PM: Resume from disk failed.
[ 0.296212] registered taskstats version 1
[ 0.296467] Magic number: 6:379:395
[ 0.296605] pci 0000:00:07.0: hash matches
[ 0.296753] rtc_cmos 00:04: setting system clock to 2010-12-20 19:21:58 UTC (1292872918)
[ 0.296815] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.296867] EDD information not available.
[ 0.297022] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[ 0.634457] usb 1-1: new low speed USB device using uhci_hcd and address 2
[ 0.894604] isapnp: No Plug & Play device found
[ 0.956089] Freeing initrd memory: 10512k freed
[ 0.976822] Freeing unused kernel memory: 684k freed
[ 0.978308] Write protecting the kernel text: 4932k
[ 0.978399] Write protecting the kernel read-only data: 1976k
[ 1.014813] udev[63]: starting version 163
[ 1.030828] usb 1-2: new full speed USB device using uhci_hcd and address 3
[ 1.294681] pata_via 0000:00:07.1: version 0.3.4
[ 1.334484] ne2k-pci.c:v1.03 9/22/2003 D. Becker/P. Gortmaker
[ 1.336189] scsi0 : pata_via
[ 1.347604] Floppy drive(s): fd0 is 1.44M
[ 1.370587] scsi1 : pata_via
[ 1.372951] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xa400 irq 14
[ 1.373008] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xa408 irq 15
[ 1.377072] FDC 0 is a post-1991 82077
[ 1.377183] ne2k-pci 0000:00:0d.0: PCI INT A -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
[ 1.379315] eth0: RealTek RTL-8029 found at 0xc000, IRQ 11, 00:00:1c:09:b4:5c.
[ 1.544630] ata1.00: ATA-6: HDS722512VLAT80, V33OA60A, max UDMA/100
[ 1.544693] ata1.00: 241254720 sectors, multi 16: LBA48
[ 1.568631] ata1.00: configured for UDMA/100
[ 1.568893] scsi 0:0:0:0: Direct-Access ATA HDS722512VLAT80 V33O PQ: 0 ANSI: 5
[ 1.569273] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.569916] sd 0:0:0:0: [sda] 241254720 512-byte logical blocks: (123 GB/115 GiB)
[ 1.570068] sd 0:0:0:0: [sda] Write Protect is off
[ 1.570119] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.570158] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.570478] sda: sda1 sda2 < sda5 sda6 sda7 >
[ 1.608783] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.732361] ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-H10A, JL02, max UDMA/33
[ 1.748364] ata2.00: configured for UDMA/33
[ 1.754067] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-H10A JL02 PQ: 0 ANSI: 5
[ 1.766846] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.766920] Uniform CD-ROM driver Revision: 3.20
[ 1.767712] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.767952] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 1.771972] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
[ 1.772098] PCI: setting IRQ 5 as level-triggered
[ 1.772106] firewire_ohci 0000:00:0a.0: PCI INT A -> Link[LNKC] -> GSI 5 (level, low) -> IRQ 5
[ 1.795452] usbcore: registered new interface driver hiddev
[ 1.808847] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:07.2/usb1/1-1/1-1:1.0/input/input3
[ 1.809426] generic-usb 0003:046D:C00E.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:07.2-1/input0
[ 1.809922] usbcore: registered new interface driver usbhid
[ 1.809978] usbhid: USB HID core driver
[ 1.880048] firewire_ohci: Added fw-ohci device 0000:00:0a.0, OHCI v1.0, 8 IR + 8 IT contexts, quirks 0x1
[ 2.372265] firewire_core: created device fw0: GUID 0011060000003669, S400
[ 2.476170] EXT4-fs (sda6): INFO: recovery required on readonly filesystem
[ 2.476304] EXT4-fs (sda6): write access will be enabled during recovery
[ 2.571863] EXT4-fs (sda6): recovery complete
[ 2.601788] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[ 4.551088] Adding 6373372k swap on /dev/sda5. Priority:-1 extents:1 across:6373372k
[ 5.428518] udev[291]: starting version 163
[ 6.423709] cfg80211: Calling CRDA to update world regulatory domain
[ 6.478582] parport_pc: VIA 686A/8231 detected
[ 6.478592] parport_pc: probing current configuration
[ 6.478611] parport_pc: Current parallel port base: 0x378
[ 6.478687] parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
[ 6.537136] lp: driver loaded but no devices found
[ 6.576282] lp0: using parport0 (interrupt-driven).
[ 6.576288] parport_pc: VIA parallel port: io=0x378, irq=7
[ 6.617925] ACPI: resource vt596_smbus [io 0x5000-0x5007] conflicts with ACPI region SM06 [??? 0x00005006 flags 0x36]
[ 6.617933] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 6.704855] ACPI: resource via686a [io 0x6000-0x607f] conflicts with ACPI region IP3_ [??? 0x0000603a flags 0x5f]
[ 6.704862] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 6.940070] ppdev: user-space parallel port driver
[ 7.128536] shpchp 0000:00:01.0: HPC vendor_id 1022 device_id 700f ss_vid 0 ss_did 0
[ 7.128548] shpchp 0000:00:01.0: Cannot reserve MMIO region
[ 7.130144] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 7.148379] Linux agpgart interface v0.103
[ 7.197308] agpgart-amdk7 0000:00:00.0: AMD 761 chipset
[ 7.228513] agpgart-amdk7 0000:00:00.0: AGP aperture is 128M @ 0xe0000000
[ 7.709745] type=1400 audit(1292872925.909:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient3" pid=469 comm="apparmor_parser"
[ 7.710143] type=1400 audit(1292872925.909:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=469 comm="apparmor_parser"
[ 7.710370] type=1400 audit(1292872925.909:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=469 comm="apparmor_parser"
[ 7.995800] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[ 7.995808] Disabling lock debugging due to kernel taint
[ 8.219676] [fglrx] Maximum main memory to use for locked dma buffers: 425 MBytes.
[ 8.219816] [fglrx] vendor: 1002 device: 9495 count: 1
[ 8.220080] [fglrx] ioport: bar 1, base 0x9000, size: 0x100
[ 8.220662] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
[ 8.220668] PCI: setting IRQ 10 as level-triggered
[ 8.220677] pci 0000:01:05.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, low) -> IRQ 10
[ 8.220849] [fglrx] Kernel PAT support is enabled
[ 8.220895] [fglrx] module loaded - fglrx 8.78.30 [Sep 20 2010] with 1 minors
[ 8.266856] cfg80211: World regulatory domain updated:
[ 8.266864] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 8.266869] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.266873] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.266877] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.266880] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.266884] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.655700] phy0: Selected rate control algorithm 'minstrel'
[ 8.656721] Registered led device: rt73usb-phy0::radio
[ 8.656749] Registered led device: rt73usb-phy0::assoc
[ 8.656774] Registered led device: rt73usb-phy0::quality
[ 8.662409] usbcore: registered new interface driver rt73usb
[ 9.302058] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
[ 9.302069] HDA Intel 0000:01:05.1: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 9.889699] VIA 82xx Audio 0000:00:07.5: PCI INT C -> Link[LNKC] -> GSI 5 (level, low) -> IRQ 5
[ 9.889846] VIA 82xx Audio 0000:00:07.5: setting latency timer to 64
[ 10.658203] EXT4-fs (sda6): re-mounted. Opts: errors=remount-ro
[ 12.104287] type=1400 audit(1292872930.305:5): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=797 comm="apparmor_parser"
[ 12.107541] type=1400 audit(1292872930.305:6): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient3" pid=806 comm="apparmor_parser"
[ 12.107984] type=1400 audit(1292872930.305:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=806 comm="apparmor_parser"
[ 12.108818] type=1400 audit(1292872930.309:8): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=806 comm="apparmor_parser"
[ 12.271903] type=1400 audit(1292872930.469:9): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=807 comm="apparmor_parser"
[ 12.278670] type=1400 audit(1292872930.477:10): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer" pid=807 comm="apparmor_parser"
[ 12.283163] type=1400 audit(1292872930.481:11): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=807 comm="apparmor_parser"
[ 13.833384] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 24.456039] eth0: no IPv6 routers present
[ 49.393186] hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.
[ 50.424253] EXT4-fs (sda6): re-mounted. Opts: errors=remount-ro,commit=0

[evolution]

Can you post me an output of "cat /boot/grub/menu.lst"?

It seems your kernel is booting into "single" mode, reading your dmesg output:

Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.35-22-generic root=UUID=e9ce018e-e87e-49dc-865a-25e6b7d5565e ro single nomodeset

If so, change your menu.lst file (if you're in stuck in the console, type "sudo nano /boot/grub/menu.lst" without the quotes) and delete the "single" line.

The rest seems to be ok...

Cheers

[evolution]

p.s. Alternatively, edit your boot.cfg file graphically with your Ubuntu live cd / pen drive...

[Anfanglir]

Thanx
I use grub 2, here is the content of /edtc/default/grub:

# If you change this file, run 'update-grub' afterwards to update
# /boot/grub/grub.cfg.

GRUB_DEFAULT=0
#GRUB_HIDDEN_TIMEOUT=0
GRUB_HIDDEN_TIMEOUT_QUIET=true
GRUB_TIMEOUT=10
GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian`
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash"
GRUB_CMDLINE_LINUX="nomodeset"

# Uncomment to enable BadRAM filtering, modify to suit your needs
# This works with Linux (no patch required) and with any kernel that obtains
# the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...)
#GRUB_BADRAM="0x01234567,0xfefefefe,0x89abcdef,0xe fefefef"

# Uncomment to disable graphical terminal (grub-pc only)
#GRUB_TERMINAL=console

# The resolution used on graphical terminal
# note that you can use only modes which your graphic card supports via VBE
# you can see them in real GRUB with the command `vbeinfo'
#GRUB_GFXMODE=640x480

# Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux
#GRUB_DISABLE_LINUX_UUID=true

# Uncomment to disable generation of recovery mode menu entries
#GRUB_DISABLE_LINUX_RECOVERY="true"

# Uncomment to get a beep at grub start
#GRUB_INIT_TUNE="480 440 1"


I added the "nomodeset" part to disable KMS, i googled this as a possible solution to ATi problems, it didnt't help so I have now removed the "nomodeset" again.

The xorg.conf look like this:

Section "Monitor"
Identifier "aticonfig-Monitor[0]-0"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection

Section "Screen"
Identifier "aticonfig-Screen[0]-0"
Device "aticonfig-Device[0]-0"
Monitor "aticonfig-Monitor[0]-0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection

Section "Module"
Load "glx"
EndSection

Section "ServerLayout"
Identifier "aticonfig Layout"
Screen 0 "aticonfig-Screen[0]-0" 0 0
EndSection

Section "Device"
Identifier "aticonfig-Device[0]-0"
BusID "PCI:1:5:0"
Driver "fglrx"
EndSection


/ Anfanglir

[evolution]

1. You have to disable kernel modesetting (the "nomodeset" line was OK), or then, you'll have lots of trouble with Catalyst...

2. It's not the /etc/default/grub file that I was talking to you (it's the /boot/grub/menu.lst one)... /etc/default/grub is going to generate you a "default" grub file when you, for instance, update you kernel...

Cheers

[Anfanglir]

1. You have to disable kernel modesetting (the "nomodeset" line was OK), or then, you'll have lots of trouble with Catalyst...

2. It's not the /etc/default/grub file that I was talking to you (it's the /boot/grub/menu.lst one)... /etc/default/grub is going to generate you a "default" grub file when you, for instance, update you kernel...

Cheers

OK, thanx

There is no menu.lst though with Grub2, but there is a grub.cfg in that directory, could that be it:

#
# DO NOT EDIT THIS FILE
#
# It is automatically generated by grub-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
#

### BEGIN /etc/grub.d/00_header ###
if [ -s $prefix/grubenv ]; then
set have_grubenv=true
load_env
fi
set default="0"
if [ "${prev_saved_entry}" ]; then
set saved_entry="${prev_saved_entry}"
save_env saved_entry
set prev_saved_entry=
save_env prev_saved_entry
set boot_once=true
fi

function savedefault {
if [ -z "${boot_once}" ]; then
saved_entry="${chosen}"
save_env saved_entry
fi
}

function recordfail {
set recordfail=1
if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi
}

function load_video {
insmod vbe
insmod vga
}

insmod part_msdos
insmod ext2
set root='(hd0,msdos6)'
search --no-floppy --fs-uuid --set e9ce018e-e87e-49dc-865a-25e6b7d5565e
if loadfont /usr/share/grub/unicode.pf2 ; then
set gfxmode=640x480
load_video
insmod gfxterm
fi
terminal_output gfxterm
insmod part_msdos
insmod ext2
set root='(hd0,msdos6)'
search --no-floppy --fs-uuid --set e9ce018e-e87e-49dc-865a-25e6b7d5565e
set locale_dir=($root)/boot/grub/locale
set lang=sv
insmod gettext
if [ "${recordfail}" = 1 ]; then
set timeout=-1
else
set timeout=10
fi
### END /etc/grub.d/00_header ###

### BEGIN /etc/grub.d/05_debian_theme ###
set menu_color_normal=white/black
set menu_color_highlight=black/light-gray
### END /etc/grub.d/05_debian_theme ###

### BEGIN /etc/grub.d/10_linux ###
menuentry 'Ubuntu, with Linux 2.6.35-22-generic' --class ubuntu --class gnu-linux --class gnu --class os {
recordfail
insmod part_msdos
insmod ext2
set root='(hd0,msdos6)'
search --no-floppy --fs-uuid --set e9ce018e-e87e-49dc-865a-25e6b7d5565e
linux /boot/vmlinuz-2.6.35-22-generic root=UUID=e9ce018e-e87e-49dc-865a-25e6b7d5565e ro quiet splash
initrd /boot/initrd.img-2.6.35-22-generic
}
menuentry 'Ubuntu, with Linux 2.6.35-22-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os {
recordfail
insmod part_msdos
insmod ext2
set root='(hd0,msdos6)'
search --no-floppy --fs-uuid --set e9ce018e-e87e-49dc-865a-25e6b7d5565e
echo 'Loading Linux 2.6.35-22-generic ...'
linux /boot/vmlinuz-2.6.35-22-generic root=UUID=e9ce018e-e87e-49dc-865a-25e6b7d5565e ro single
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-2.6.35-22-generic
}
### END /etc/grub.d/10_linux ###

### BEGIN /etc/grub.d/20_linux_xen ###
### END /etc/grub.d/20_linux_xen ###

### BEGIN /etc/grub.d/20_memtest86+ ###
menuentry "Memory test (memtest86+)" {
insmod part_msdos
insmod ext2
set root='(hd0,msdos6)'
search --no-floppy --fs-uuid --set e9ce018e-e87e-49dc-865a-25e6b7d5565e
linux16 /boot/memtest86+.bin
}
menuentry "Memory test (memtest86+, serial console 115200)" {
insmod part_msdos
insmod ext2
set root='(hd0,msdos6)'
search --no-floppy --fs-uuid --set e9ce018e-e87e-49dc-865a-25e6b7d5565e
linux16 /boot/memtest86+.bin console=ttyS0,115200n8
}
### END /etc/grub.d/20_memtest86+ ###

### BEGIN /etc/grub.d/30_os-prober ###
menuentry "Ubuntu 8.04.4 LTS, kernel 2.6.24-28-generic (on /dev/sda1)" {
insmod part_msdos
insmod ext2
set root='(hd0,msdos1)'
search --no-floppy --fs-uuid --set 3b12d5c7-5bac-4b2b-a1a0-794c4c22ba48
linux /boot/vmlinuz-2.6.24-28-generic root=UUID=3b12d5c7-5bac-4b2b-a1a0-794c4c22ba48 ro quiet splash
initrd /boot/initrd.img-2.6.24-28-generic
}

### END /etc/grub.d/30_os-prober ###

### BEGIN /etc/grub.d/40_custom ###
# This file provides an easy way to add custom menu entries. Simply type the
# menu entries you want to add after this comment. Be careful not to change
# the 'exec tail' line above.
### END /etc/grub.d/40_custom ###

### BEGIN /etc/grub.d/41_custom ###
if [ -f $prefix/custom.cfg ]; then
source $prefix/custom.cfg;
fi
### END /etc/grub.d/41_custom ###


(I edited out a bunch of different kernel versions of 8.04 LTS)

/ Anfanglir

[PsynoKhi0]

[ 8.220849] [fglrx] Kernel PAT support is enabled

Wasn't that a picky option on AGP cards? Like you had to add something similar to "nopat" to the kernel boot options...
Try searching the forums for this, it rings a bell here

[PsynoKhi0]

*1 minute edit windoooooooooooow...
1 minute edit windoooooooooow...
I hope your death will be painfully sloooooooooooow...
Can you cause me anything but wooooooooooOOOOOOO*cough*OOOEeeeeEee...*

BTW what does your xorg.conf look like?
Specs on your PSU?