Page 2 of 2 FirstFirst 12
Results 11 to 12 of 12

Thread: ATI 8.42.3 + openSuSE10.3 x64 = several problems

  1. #11
    Join Date
    Oct 2007
    Posts
    31

    Default

    Just an update on what i've got so far.
    After several uninstalls/installs with few improvements... i did it one more time for the 8.42.3 drivers, following the openSUSE_ATI_HOWTO "hard way".
    But this time i did everything without X, using "init 3" at boot, and rebooting after "cleaning" the previous drivers, after the "aticonfig" command and finally after configuring sax2.

    And i've got a lot of improvements:
    1. The info i get from glxinfo and fglrxinfo is the same as before.
    2. fgl_glxgears runs fine now
    3. no desktop corruption (watermark issue) so far (crosses fingers)
    4. Warsow, Nexuiz, Tremulous and the ETQW.demo all run fine
    5. Google earth runs fine.

    negatives:
    1. amd catalyst control center still refuses to run:
    HTML Code:
    KTPORTLin:/home/kmz # amdcccle
    amdcccle: xcb_xlib.c:52: xcb_xlib_unlock: Assertion `c->xlib.lock' failed. Aborted
    2. sax2 still "freezes" when exiting, but this only happens if i start it from init 3... and it doesn't really freeze either, i think it just gets the wrong monitor/card parameters on exit, because i can still type reboot->enter and it works... i can even see a green "blur" while it "works" to reboot.

    Haven't tested for suspend to ram/disk ou powerplay settings (Using a X700 mobile here).

    Regarding compiz-fusion... i'm still confused a bit about compiz/compiz.fusion/beryl really are or do, or if i just need one etc etc... either way, i installed compiz-fusion 0.6 and followed these instructions here to get it to work, using aiglx.
    It runs fine... the first time. Performance is acceptable i guess, but it could be smother. Resizing windows feels very slow... but now i've confirmed it is the same without even using compiz.
    After rebooting i get a problem with windows decorations - no close/maximize/minimize buttons. There must be some problem with the windows decorator setting.. kde ou emerald. Still looking for info on that, but i don't think it's driver related

    regards,
    Carlos

  2. #12
    Join Date
    Oct 2007
    Posts
    31

    Default

    Just an update on what i've got so far.
    After several uninstalls/installs with few improvements... i did it one more time for the 8.42.3 drivers, following the openSUSE_ATI_HOWTO "hard way".
    But this time i did everything without X, using "init 3" at boot, and rebooting after "cleaning" the previous drivers, after the "aticonfig" command and finally after configuring sax2.

    And i've got a lot of improvements:
    1. The info i get from glxinfo and fglrxinfo is the same as before.
    2. fgl_glxgears runs fine now
    3. no desktop corruption (watermark issue) so far (crosses fingers)
    4. Warsow, Nexuiz, Tremulous and the ETQW.demo all run fine
    5. Google earth runs fine.

    negatives:
    1. amd catalyst control center still refuses to run:
    HTML Code:
    KTPORTLin:/home/kmz # amdcccle
    amdcccle: xcb_xlib.c:52: xcb_xlib_unlock: Assertion `c->xlib.lock' failed.
    Aborted
    2. sax2 still "freezes" when exiting, but this only happens if i start it from init 3... and it doesn't really freeze either, i think it just gets the wrong monitor/card parameters on exit, because i can still type reboot->enter and it works... i can even see a green "blur" while it "works" to reboot.

    Haven't tested for suspend to ram/disk ou powerplay settings (Using a X700 mobile here).

    Regarding compiz-fusion... i'm still confused a bit about compiz/compiz.fusion/beryl really are or do, or if i just need one etc etc... either way, i installed compiz-fusion 0.6 and followed these instructions here to get it to work, using aiglx.
    It runs fine... the first time. Performance is acceptable i guess, but it could be smother. Resizing windows is very slow... but now i've confirmed it is the same without even using compiz.

    After rebooting i get a problem with windows decorations - no close/maximize/minimize buttons. There must be some problem with the windows decorator setting.. kde ou emerald. Still looking for info on that, but i shouldn't be a driver problem.

    regards,
    Carlos

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •